Announcement

Collapse
No announcement yet.

AMF Machine

Collapse

Adsense Classic 2

Collapse

Adsense Mobile 320x100 Left

Collapse
X
Collapse

  • AMF Machine



    Show of hands. How many have seen some of these?
    Attached Files

    • Grit
      #17
      Grit commented
      Editing a comment
      I'd really love to see her chooch some balls up the track but in the mean time, are they stuffing sound muffling insulation under the cribbing? Also, the "lift" doesn't look too different from a vertangled one...The different parts would be the mounting and paddle system?

    • Ted
      #18
      Ted commented
      Editing a comment
      Originally posted by Grit View Post
      I'd really love to see her chooch some balls up the track but in the mean time, are they stuffing sound muffling insulation under the cribbing? Also, the "lift" doesn't look too different from a vertangled one...The different parts would be the mounting and paddle system?
      The horizontal 'lift' is more narrow as is the belt and a bit linger. Only has one drive pulley from the motor above. Paddle mounts high in the back and the arm reaches down instead of up as we know it. There are 2 pulleys on each BE motor. One for each carpet drive, and the other goes to the 2 pulleys with Sprague clutches for running the rudder drive from either machine. The Japanese also added a 115 v relay from each BE motor so when both of the BE motors have timed out, the HRB motor stops as well.
      And yes, since there is a mall level below, the insulation is for sound.

    • KLH
      #19
      KLH commented
      Editing a comment
      Early testing of 8290`s had HBR`s I was in Virginia attending pinspotter school and the mechanic of major league had HBRS.Said he had alot of pins in subways on those pairs of lanes. PBL`S work just fine very few issues
    Posting comments is disabled.

Other Technical Articles

Collapse

  • ProTech
    Working Safely
    ProTech
    Just a reminder to work Safely !

    http://www.safetynewsalert.com/worke...ter-112k-fine/
    12-04-2011, 08:34 PM
  • PJ
    My luck ran out - ** Warning Graphic Content **
    PJ
    Was working senior league (full house) last Tuesday. Was having turn pan issues on lane 18. Reached in to get a pin off the track before ball came up. Got to close to cross conveyor belt. Felt my finger getting grabbed. Pulled back and lost the tip in the lower pulley. If I hadn't might have lost my whole finger. The night shift pinchaser found the tip on shaker board. The surgeon had to snip part of the bone off to be able to sew the skin and meat around the tip of the finger. No, I am not trying to be macho about...
    02-11-2012, 12:14 PM
  • 8270king
    King tip of the day - Chassis plugs
    8270king
    I use a wire tie rather than the nuts and U bolts to clamp wires on the C1 plugs.

    It is much quicker to get in if you have an issue - and I had a bad socket today on lane 1

    Just clip the wire tie and you are in

    When finished just re-install a wire tie





    ...
    04-06-2012, 10:12 AM
  • shamefowjze
    Cleaner Tank Filter Advice
    shamefowjze
    You can not use the brass filter in the cleaner. Lane cleaners are aggressive and corrodes the brass. It gets ugly real fast. Mike, This is what I do: 2 wraps of teflon tape on the fitting, then I hand screw that into the filter hand tight, Then I snug it with a wrench and channel locks about 1/8 of a turn. For the filter I use 2 wraps of telfon tape and a bead of silicone around the threads at the beginning of the threads. I then screw that into the tank hand tight. It's a low pressure application so there is no need to ...
    04-22-2012, 10:59 AM
  • clutchplate
    XLI Elevator Strips
    clutchplate
    Is it important to replace the grey riveted elevator strips? I know without it the elevator has a lot of play. Or is it mainly to dampen the sound.

    To see answers and the rest of this thread CLICK HERE
    04-28-2012, 12:55 PM
  • PinCup
    DMX512 lighting 101
    PinCup
    I'm once again sorting out and Cosmic Bowling light show that never worked or looked quite right. I am always amazed at what was a 'professional' install, where basic DMX rules are ignored. So, to help inform my BT brothers and sisters, I'll start a thread to help inform. Here's what I've learned over the years. What is DMX512 protocol? DXM lighting protocol is a system of controlling your light show. Used in night clubs, theater and stage productions, landscape accent, and by those crazy folks that put a million lights on their house for the holidays. DMX allows you to remote control intelligent and non-intelligent lighting fixtures. Now days, you can even control DMX from your smart phone. Control of a non-intelligent light fi...
    05-13-2012, 08:31 PM

Article Tags

Collapse

There are no tags yet.

Adsense Featured 2

Collapse

Latest Articles

Collapse

Working...
X