No announcement yet.

Rebuilding an electrical box (with pics)


Adsense Classic 2


Adsense Mobile 320x100 Left


  • Rebuilding an electrical box (with pics)

    This is a before and after shot of our boxes. The rewired one has all connections that I can unplug this box and bench test it. Click image for larger version

Name:	ebox 005.JPG
Views:	2
Size:	84.5 KB
ID:	1065725Click image for larger version

Name:	ebox 003.JPG
Views:	2
Size:	78.9 KB
ID:	1065726
      Posting comments is disabled.

    Other Technical Articles


    • ProTech
      Working Safely
      Just a reminder to work Safely !
      12-04-2011, 07:34 PM
    • PJ
      My luck ran out - ** Warning Graphic Content **
      Was working senior league (full house) last Tuesday. Was having turn pan issues on lane 18. Reached in to get a pin off the track before ball came up. Got to close to cross conveyor belt. Felt my finger getting grabbed. Pulled back and lost the tip in the lower pulley. If I hadn't might have lost my whole finger. The night shift pinchaser found the tip on shaker board. The surgeon had to snip part of the bone off to be able to sew the skin and meat around the tip of the finger. No, I am not trying to be macho about...
      02-11-2012, 11:14 AM
    • 8270king
      King tip of the day - Chassis plugs
      I use a wire tie rather than the nuts and U bolts to clamp wires on the C1 plugs.

      It is much quicker to get in if you have an issue - and I had a bad socket today on lane 1

      Just clip the wire tie and you are in

      When finished just re-install a wire tie

      04-06-2012, 09:12 AM
    • shamefowjze
      Cleaner Tank Filter Advice
      You can not use the brass filter in the cleaner. Lane cleaners are aggressive and corrodes the brass. It gets ugly real fast. Mike, This is what I do: 2 wraps of teflon tape on the fitting, then I hand screw that into the filter hand tight, Then I snug it with a wrench and channel locks about 1/8 of a turn. For the filter I use 2 wraps of telfon tape and a bead of silicone around the threads at the beginning of the threads. I then screw that into the tank hand tight. It's a low pressure application so there is no need to ...
      04-22-2012, 09:59 AM
    • clutchplate
      XLI Elevator Strips
      Is it important to replace the grey riveted elevator strips? I know without it the elevator has a lot of play. Or is it mainly to dampen the sound.

      To see answers and the rest of this thread CLICK HERE
      04-28-2012, 11:55 AM
    • PinCup
      DMX512 lighting 101
      I'm once again sorting out and Cosmic Bowling light show that never worked or looked quite right. I am always amazed at what was a 'professional' install, where basic DMX rules are ignored. So, to help inform my BT brothers and sisters, I'll start a thread to help inform. Here's what I've learned over the years. What is DMX512 protocol? DXM lighting protocol is a system of controlling your light show. Used in night clubs, theater and stage productions, landscape accent, and by those crazy folks that put a million lights on their house for the holidays. DMX allows you to remote control intelligent and non-intelligent lighting fixtures. Now days, you can even control DMX from your smart phone. Control of a non-intelligent light fi...
      05-13-2012, 07:31 PM

    Article Tags


    There are no tags yet.

    Adsense Featured 2


    Latest Articles


    • Slowing Down Pinsetter
      I know this has been talked about before, but I have some specific questions regarding slowing down our A-2's to A speed. We have the dual pulleys on the motors (both the gear box and elevator pulleys
      11-14-2013, 10:47 PM
    • Blue A2 Rebuild
      [ATTACH=CONFIG]5916[/ATTACH]Smurf Blue A2's. I switched to a lighter color blue on these machines and I think they look nicer with the gray instead of black. I'm not quite finished with these yet- waiting on new rake shafts,
      10-21-2013, 08:07 PM
    • Here are some pics:
      [ATTACH=CONFIG]5869[/ATTACH][ATTACH=CONFIG]5867[/ATTACH][ATTACH=CONFIG]5868[/ATTACH](Sorry, kinda blurry. I'll take more if you need 'em)
      10-15-2013, 08:02 PM
    • Measuring deck/scissor cable length
      Re: Deck cable length
      Control cable-41 1/2", two closed loops.
      Upper sissor cable-43 11/16, one closed loop, one right hand thread coupler.
      Upper moving deck cable-45 11/16", one
      10-08-2013, 10:14 PM
    • 270 stop
      Steve Stafford (JBEES)
      The movement you are seeing is in the actuator links moving down a bit at 180?

      This can be caused by a couple of things. What style plunger lever are you using? Stamped version or the original
      10-05-2013, 06:20 PM
    • Gearbox Rebuild
      [ATTACH=CONFIG]5722[/ATTACH] How would I go about removing that bearing at the end of the shaft (or is it even possible?) CLICK HERE TO VIEW THREAD
      09-09-2013, 12:47 PM