Announcement

Collapse
No announcement yet.

Starting the overlays with pictures

Collapse

Adsense Classic 2

Collapse

Adsense Mobile 320x100 Left

Collapse
X
Collapse

  • Starting the overlays with pictures

    Ok as promised Day 2 of the overlays. Not much happening finishing sanding the lanes.

    Click image for larger version

Name:	SAM_0173.jpg
Views:	2
Size:	53.7 KB
ID:	1065728
    Click image for larger version

Name:	SAM_0174.jpg
Views:	2
Size:	57.8 KB
ID:	1065729
    These pics are at the dots on the heads. Put 2 extra 6" lane screws on the 13th boards of each side, every other stringer on the foundation. Also notice some of the dots are gone, also have some red dots, and hitting nails.



    These last 2 pics are the thickness of one of the lanes. The first one is the pine area and the second is the maple area. As you can see getting close to the tongue and groove. These lanes are about 25yrs. old don't know exactly though. When I was here for 15 yrs. They were sanded every year.



    Tomorrow or the next day removing the heads section. Also, tomorrow will be doing clean up and the overlays will be delivered. Be removing the F.E. lifts to shim up. More pics tomorrw. Laters
    Attached Files
      Posting comments is disabled.

    Other Technical Articles

    Collapse

    • ProTech
      Working Safely
      ProTech
      Just a reminder to work Safely !

      http://www.safetynewsalert.com/worke...ter-112k-fine/
      12-04-2011, 08:34 PM
    • PJ
      My luck ran out - ** Warning Graphic Content **
      PJ
      Was working senior league (full house) last Tuesday. Was having turn pan issues on lane 18. Reached in to get a pin off the track before ball came up. Got to close to cross conveyor belt. Felt my finger getting grabbed. Pulled back and lost the tip in the lower pulley. If I hadn't might have lost my whole finger. The night shift pinchaser found the tip on shaker board. The surgeon had to snip part of the bone off to be able to sew the skin and meat around the tip of the finger. No, I am not trying to be macho about...
      02-11-2012, 12:14 PM
    • 8270king
      King tip of the day - Chassis plugs
      8270king
      I use a wire tie rather than the nuts and U bolts to clamp wires on the C1 plugs.

      It is much quicker to get in if you have an issue - and I had a bad socket today on lane 1

      Just clip the wire tie and you are in

      When finished just re-install a wire tie





      ...
      04-06-2012, 10:12 AM
    • shamefowjze
      Cleaner Tank Filter Advice
      shamefowjze
      You can not use the brass filter in the cleaner. Lane cleaners are aggressive and corrodes the brass. It gets ugly real fast. Mike, This is what I do: 2 wraps of teflon tape on the fitting, then I hand screw that into the filter hand tight, Then I snug it with a wrench and channel locks about 1/8 of a turn. For the filter I use 2 wraps of telfon tape and a bead of silicone around the threads at the beginning of the threads. I then screw that into the tank hand tight. It's a low pressure application so there is no need to ...
      04-22-2012, 10:59 AM
    • clutchplate
      XLI Elevator Strips
      clutchplate
      Is it important to replace the grey riveted elevator strips? I know without it the elevator has a lot of play. Or is it mainly to dampen the sound.

      To see answers and the rest of this thread CLICK HERE
      04-28-2012, 12:55 PM
    • PinCup
      DMX512 lighting 101
      PinCup
      I'm once again sorting out and Cosmic Bowling light show that never worked or looked quite right. I am always amazed at what was a 'professional' install, where basic DMX rules are ignored. So, to help inform my BT brothers and sisters, I'll start a thread to help inform. Here's what I've learned over the years. What is DMX512 protocol? DXM lighting protocol is a system of controlling your light show. Used in night clubs, theater and stage productions, landscape accent, and by those crazy folks that put a million lights on their house for the holidays. DMX allows you to remote control intelligent and non-intelligent lighting fixtures. Now days, you can even control DMX from your smart phone. Control of a non-intelligent light fi...
      05-13-2012, 08:31 PM

    Article Tags

    Collapse

    There are no tags yet.

    Adsense Featured 2

    Collapse

    Latest Articles

    Collapse

    • Legends Pin Deck Treatment Product Infomation Request
      megatron
      I've been searching for a while now for more information about Legends Pin Deck Treatment, but I can't find anything.The directions on the spray bottle say not to over apply, but what is the normal amount
      05-18-2015, 10:00 PM
    • machine cycles when gutter thrown on opposite lane
      Ted
      [ATTACH=CONFIG]5940[/ATTACH]I've also seen this happen when the AMF detector head is mounted solid on the nose of the kickback, and in mode '0'. The vibration of the kickback seems to jolt the electronics enough to cause cycling
      10-29-2013, 03:39 PM
    • A Project
      Tablejam
      So many years ago we had a remodel. This is lane 50 with a walkway next to it. Prior to the remodel this house was 60 lanes straight across. The last 10 lanes were covered up and a wall built on lane
      09-18-2013, 09:00 PM
    • Installed Used Synthetic Pin Decks
      don805
      [ATTACH=CONFIG]5642[/ATTACH][ATTACH=CONFIG]5656[/ATTACH][ATTACH=CONFIG]5657[/ATTACH][ATTACH=CONFIG]5658[/ATTACH][ATTACH=CONFIG]5659[/ATTACH][ATTACH=CONFIG]5660[/ATTACH][ATTACH=CONFIG]5661[/ATTACH][ATTACH=CONFIG]5662[/ATTACH][ATTACH=CONFIG]5663[/ATTACH][ATTACH=CONFIG]5664[/ATTACH][ATTACH=CONFIG]5665[/ATTACH][ATTACH=CONFIG]5655[/ATTACH][ATTACH=CONFIG]5654[/ATTACH][ATTACH=CONFIG]5653[/ATTACH][ATTACH=CONFIG]5643[/ATTACH][ATTACH=CONFIG]5644[/ATTACH][ATTACH=CONFIG]5645[/ATTACH][ATTACH=CONFIG]5646[/ATTACH][ATTACH=CONFIG]5647[/ATTACH][ATTACH=CONFIG]5648[/ATTACH][ATTACH=CONFIG]5649[/ATTACH][ATTACH=CONFIG]5650[/ATTACH][ATTACH=CONFIG]5651[/ATTACH][ATTACH=CONFIG]5652[/ATTACH][ATTACH=CONFIG]5666[/ATTACH]

      We just spent two days removing our old wooden pin decks and installing synthetic decks
      08-25-2013, 11:52 PM
    • Replacing Kickback?
      Ted
      [ATTACH=CONFIG]5324[/ATTACH][ATTACH=CONFIG]5325[/ATTACH]Build a rigid support for the torque tube. This one is 1/4" short of the measurement. I use door shims to snug it to the proper height as i go across the house replacing kickbacks.
      07-20-2013, 12:29 AM
    • Gold Crown Masking Units & Crown Imperial Ball Return Installed Pics
      MattC
      More detailed photos of my LED pinfinder system.

      The LED controller circuit board receives a switch closure from each of the pin switches on the moving deck and latches the corresponding
      07-02-2013, 03:11 PM
    Working...
    X