Announcement

Collapse
No announcement yet.

QubicaAMF

Collapse

Adsense Classic 2

Collapse

Adsense Mobile 320x100 Right

Collapse
  • Filter
  • Time
  • Show
Clear All
new posts

  • King tip of the day - Chassis plugs

    King tip of the day - Chassis plugs

    I use a wire tie rather than the nuts and U bolts to clamp wires on the C1 plugs.

    It is much quicker to get in if you have an issue - and I had a bad socket today on lane 1

    Just clip the wire tie and you are in

    When finished just re-install a wire tie





    ...
    See more | Go to post

  • XLI Elevator Strips

    XLI Elevator Strips

    Is it important to replace the grey riveted elevator strips? I know without it the elevator has a lot of play. Or is it mainly to dampen the sound.

    To see answers and the rest of this thread CLICK HERE
    See more | Go to post

  • Instructomat LED on chassis

    Instructomat LED on chassis

    Ok, here are some pics of one of our chassis with the LED for instructomat. We use these LEDs as they come wired complete with bezel and inline resistor for around AU$3.50 : http://www.jaycar.com.au/productView.asp?ID=SL2646 They look good too!

    The red cable from the LED runs to the motherboard, pin #5 on the PC#1 slot. We just drilled a small hole in the board and soldered it (carefully)to the trace.

    The black cable from the LED (with resistor) runs to ground, in this case there is also a diode (N4004) inline as well. Of...
    See more | Go to post

  • Wyse Terminal Funcion Key setup

    Wyse Terminal Funcion Key setup

    The attached PDF gives instructions for setting up the functions keys for a Wyse terminal.

    If you're running AccuDesk with AccuScore Plus you'll definitely want to learn how to do this....
    See more | Go to post
There are no articles in this category.
  • Filter
  • Time
  • Show
Clear All
new posts
Please log in to your account to view your subscribed posts.

Latest Articles

Collapse

  • Wyse Terminal Funcion Key setup
    deb
    The attached PDF gives instructions for setting up the functions keys for a Wyse terminal.

    If you're running AccuDesk with AccuScore Plus you'll definitely want to learn how to do this....
    02-05-2014, 09:32 AM
  • National Combo Gearbox Case Repair
    BulldogMike
    [ATTACH=CONFIG]5392[/ATTACH]I had a couple of National Combo gearboxes that had cracks in the bearing seat. Eric @ Stahls made a plate and machined out the old part. It has been running for a couple of months without issue.
    08-02-2013, 11:06 PM
  • Converting To Expanders
    8270king
    07-30-2013, 09:47 AM
  • Sloppy pinwheels xli
    Fred H
    [ATTACH=CONFIG]5330[/ATTACH]I add an extra nylon washer behind the rollers to take most of the slop out
    07-20-2013, 12:32 AM
  • 82-30 6525 chassis sweep contactor chattering
    toon30s
    I have a chassis that the sweep contactor chatters on when it starts a cycle. Chassis problem, not in the machine. This is an OmegaTek conversion. I have had this chassis on my machine for 3 weeks
    07-02-2013, 03:44 PM
  • kidney rail assy, check it out
    Pin_Head
    [ATTACH=CONFIG]5224[/ATTACH][ATTACH=CONFIG]5225[/ATTACH][ATTACH=CONFIG]5226[/ATTACH]

    These are the pics of it TJ I couldnt get the video to work for some stupid reason, they come with 3 nice bushings so you don't need a shoulder bolt, any standard 5/16"
    07-01-2013, 10:42 PM

Adsense Tower Right

Collapse
Working...
X