Announcement

Collapse
No announcement yet.

QubicaAMF

Collapse

Adsense Classic 2

Collapse

Adsense Mobile 320x100 Left

Collapse
Collapse
  • Topic not found. You may have followed an invalid link or the topic may have been deleted or moved to another forum.

Other Technical Articles

Collapse

  • ProTech
    Working Safely
    ProTech
    Just a reminder to work Safely !

    http://www.safetynewsalert.com/worke...ter-112k-fine/
    12-04-2011, 08:34 PM
  • PJ
    My luck ran out - ** Warning Graphic Content **
    PJ
    Was working senior league (full house) last Tuesday. Was having turn pan issues on lane 18. Reached in to get a pin off the track before ball came up. Got to close to cross conveyor belt. Felt my finger getting grabbed. Pulled back and lost the tip in the lower pulley. If I hadn't might have lost my whole finger. The night shift pinchaser found the tip on shaker board. The surgeon had to snip part of the bone off to be able to sew the skin and meat around the tip of the finger. No, I am not trying to be macho about...
    02-11-2012, 12:14 PM
  • 8270king
    King tip of the day - Chassis plugs
    8270king
    I use a wire tie rather than the nuts and U bolts to clamp wires on the C1 plugs.

    It is much quicker to get in if you have an issue - and I had a bad socket today on lane 1

    Just clip the wire tie and you are in

    When finished just re-install a wire tie





    ...
    04-06-2012, 10:12 AM
  • shamefowjze
    Cleaner Tank Filter Advice
    shamefowjze
    You can not use the brass filter in the cleaner. Lane cleaners are aggressive and corrodes the brass. It gets ugly real fast. Mike, This is what I do: 2 wraps of teflon tape on the fitting, then I hand screw that into the filter hand tight, Then I snug it with a wrench and channel locks about 1/8 of a turn. For the filter I use 2 wraps of telfon tape and a bead of silicone around the threads at the beginning of the threads. I then screw that into the tank hand tight. It's a low pressure application so there is no need to ...
    04-22-2012, 10:59 AM
  • clutchplate
    XLI Elevator Strips
    clutchplate
    Is it important to replace the grey riveted elevator strips? I know without it the elevator has a lot of play. Or is it mainly to dampen the sound.

    To see answers and the rest of this thread CLICK HERE
    04-28-2012, 12:55 PM
  • PinCup
    DMX512 lighting 101
    PinCup
    I'm once again sorting out and Cosmic Bowling light show that never worked or looked quite right. I am always amazed at what was a 'professional' install, where basic DMX rules are ignored. So, to help inform my BT brothers and sisters, I'll start a thread to help inform. Here's what I've learned over the years. What is DMX512 protocol? DXM lighting protocol is a system of controlling your light show. Used in night clubs, theater and stage productions, landscape accent, and by those crazy folks that put a million lights on their house for the holidays. DMX allows you to remote control intelligent and non-intelligent lighting fixtures. Now days, you can even control DMX from your smart phone. Control of a non-intelligent light fi...
    05-13-2012, 08:31 PM

Article Tags

Collapse

There are no tags yet.

Adsense Featured 2

Collapse

Latest Articles

Collapse

  • Wyse Terminal Funcion Key setup
    deb
    The attached PDF gives instructions for setting up the functions keys for a Wyse terminal.

    If you're running AccuDesk with AccuScore Plus you'll definitely want to learn how to do this....
    02-05-2014, 09:32 AM
  • National Combo Gearbox Case Repair
    BulldogMike
    [ATTACH=CONFIG]5392[/ATTACH]I had a couple of National Combo gearboxes that had cracks in the bearing seat. Eric @ Stahls made a plate and machined out the old part. It has been running for a couple of months without issue.
    08-02-2013, 11:06 PM
  • Converting To Expanders
    8270king
    07-30-2013, 09:47 AM
  • Sloppy pinwheels xli
    Fred H
    [ATTACH=CONFIG]5330[/ATTACH]I add an extra nylon washer behind the rollers to take most of the slop out
    07-20-2013, 12:32 AM
  • 82-30 6525 chassis sweep contactor chattering
    toon30s
    I have a chassis that the sweep contactor chatters on when it starts a cycle. Chassis problem, not in the machine. This is an OmegaTek conversion. I have had this chassis on my machine for 3 weeks
    07-02-2013, 03:44 PM
  • kidney rail assy, check it out
    Pin_Head
    [ATTACH=CONFIG]5224[/ATTACH][ATTACH=CONFIG]5225[/ATTACH][ATTACH=CONFIG]5226[/ATTACH]

    These are the pics of it TJ I couldnt get the video to work for some stupid reason, they come with 3 nice bushings so you don't need a shoulder bolt, any standard 5/16"
    07-01-2013, 10:42 PM
Working...
X