Announcement

Collapse
No announcement yet.

Random Pictures

Collapse

Adsense Classic 2

Collapse

Adsense Mobile 320x100 Left

Collapse
Collapse
  • Topic not found. You may have followed an invalid link or the topic may have been deleted or moved to another forum.

Other Technical Articles

Collapse

  • ProTech
    Working Safely
    ProTech
    Just a reminder to work Safely !

    http://www.safetynewsalert.com/worke...ter-112k-fine/
    12-04-2011, 08:34 PM
  • PJ
    My luck ran out - ** Warning Graphic Content **
    PJ
    Was working senior league (full house) last Tuesday. Was having turn pan issues on lane 18. Reached in to get a pin off the track before ball came up. Got to close to cross conveyor belt. Felt my finger getting grabbed. Pulled back and lost the tip in the lower pulley. If I hadn't might have lost my whole finger. The night shift pinchaser found the tip on shaker board. The surgeon had to snip part of the bone off to be able to sew the skin and meat around the tip of the finger. No, I am not trying to be macho about...
    02-11-2012, 12:14 PM
  • 8270king
    King tip of the day - Chassis plugs
    8270king
    I use a wire tie rather than the nuts and U bolts to clamp wires on the C1 plugs.

    It is much quicker to get in if you have an issue - and I had a bad socket today on lane 1

    Just clip the wire tie and you are in

    When finished just re-install a wire tie





    ...
    04-06-2012, 10:12 AM
  • shamefowjze
    Cleaner Tank Filter Advice
    shamefowjze
    You can not use the brass filter in the cleaner. Lane cleaners are aggressive and corrodes the brass. It gets ugly real fast. Mike, This is what I do: 2 wraps of teflon tape on the fitting, then I hand screw that into the filter hand tight, Then I snug it with a wrench and channel locks about 1/8 of a turn. For the filter I use 2 wraps of telfon tape and a bead of silicone around the threads at the beginning of the threads. I then screw that into the tank hand tight. It's a low pressure application so there is no need to ...
    04-22-2012, 10:59 AM
  • clutchplate
    XLI Elevator Strips
    clutchplate
    Is it important to replace the grey riveted elevator strips? I know without it the elevator has a lot of play. Or is it mainly to dampen the sound.

    To see answers and the rest of this thread CLICK HERE
    04-28-2012, 12:55 PM
  • PinCup
    DMX512 lighting 101
    PinCup
    I'm once again sorting out and Cosmic Bowling light show that never worked or looked quite right. I am always amazed at what was a 'professional' install, where basic DMX rules are ignored. So, to help inform my BT brothers and sisters, I'll start a thread to help inform. Here's what I've learned over the years. What is DMX512 protocol? DXM lighting protocol is a system of controlling your light show. Used in night clubs, theater and stage productions, landscape accent, and by those crazy folks that put a million lights on their house for the holidays. DMX allows you to remote control intelligent and non-intelligent lighting fixtures. Now days, you can even control DMX from your smart phone. Control of a non-intelligent light fi...
    05-13-2012, 08:31 PM

Article Tags

Collapse

There are no tags yet.

Adsense Featured 2

Collapse

Latest Articles

Collapse

  • amf 82-70 table bracket snap
    AZZ_90
    after attempting to load 10 pins from the shuttle......
    10-26-2014, 05:06 AM
  • Masking units and curtain walls
    Ken-Cliff Lanes
    AMF's first commercial installation (1951) shows curtains above the "Pinvisor screens"....
    10-26-2014, 05:03 AM
  • Table temp repair...
    shaggyshawn
    Had a table crack in the usual place(shocker) no welder, don't have time to take it out go have it welded put back in etc... I'm not a fan of the table repair kit Brunswick sells but I install one anyway... And put a brace on it with self tapping screws... I think it will definitely hold up better specially if I welded it.. Lol...
    10-26-2014, 04:59 AM
  • Another one gone
    Carl D
    Well, Kelmscott Bowl is finally no more.

    After being sold twice (!) since it closed in May last year, the new owners want the building for some sort of refrigerated storage with a retail
    10-26-2014, 04:46 AM
  • Prayers for Lonnie
    Mike Wilson
    My heart is broken. What a tragic loss.

    A truly wonderful person has left us. Lonnie was one of the kindest and most trustworthy people I have ever met.

    Rest in Peace my friend.


    ...
    10-26-2014, 04:40 AM
  • accuscore help
    smalltownguy
    Sigorney is a bit far away for me.

    Here are some pictures of my setup that might help you:

    [ATTACH=CONFIG]7272[/ATTACH] Pic 1

    [ATTACH=CONFIG]7273[/ATTACH] Pic 2. Names in and score arrows up.

    [ATTACH=CONFIG]727[/ATTACH]
    07-07-2014, 06:01 AM
Working...
X