Announcement

Collapse
No announcement yet.

Bowl-Tech Rising Star 2013 Rules

Collapse

Adsense Classic 1

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Bowl-Tech Rising Star 2013 Rules

    Bowl-Tech Rising Star Award 2013
    Guidelines




    Prior to making your nomination please read the following rules and
    guidelines
    Official Voting Will Start January
    16, 2014

    Considerations
    *NEW* Bowl-Tech member who provides accurate information.
    Is courteous to other members and presents him/her self professionally.
    Person who has helped you out by sharing experiences and best practices in
    meaningful quality posts.

    Persons who qualify
    Any Bowl-Tech member who receives 3 nominations by other Bowl-Tech visitors and
    meets other criteria in the rules stated here.
    Any Bowl-Tech member who has not had their membership banned for improper site conduct at any time during the 2013 year.
    Has at Least 10 forum posts prior to December 1, 2013.
    Has not been an active
    member with a previous account in the last 5 years.
    Nominee must be a registered Bowl-Tech member on or after
    December 1, 2012 but prior to December 1, 2013.

    Persons allowed to vote
    Any person who is a current member of Bowl-Tech. To access the ballot to vote you must be logged in.
    Any person who is registered on Bowl-Tech

    The Winner
    Winning the Bowl-Tech Rising Star award is recognition by that
    new members
    peers as an outstanding contributor to Bowl-Tech and the bowling industry.

    In the event of a tie
    If there is a tie between two or more candidates there will be a run off
    lasting for 7 days in which members who tied will be the only persons listed on the
    ballot. Vote counts will start over and rules listed above will still be in
    place. If a tie exists after that the top two vote receivers will share the
    award.

    Disclaimer stuff
    This award does not indicate an endorsement by Bowl-Tech or the companies or
    individuals who have contributed to the prizes.
    Bowl-Tech Incorporated reserves the right to adjust rules as needed to
    address any issues that may arise during the voting process or remove any person
    from consideration for cheating or any other reasons deemed unethical.
    Use of the Bowl-Tech web site as a venue for ones personal campaign interests
    is considered to be unethical and will not be tolerated.

    How do I make my choice - Helpful Tips

    There are helpful tools on Bowl-Tech if you would like to research before you
    make your selection.

    You can take a look through a members posts
    just by clicking their name and then clicking the view posts link that shows
    up under their name.
    Also at the top of each page you can click the
    User List link and do an alphabetical listing of the user, then you can view
    their posts after you find them.

    Things to think about !!

    Is this person polite to other members ?

    Does he or she give accurate and meaningful
    information?


    Does this member help keep the peace?
    Mike Wilson
    Bowl-Tech Inc.

Adsense Classic 2

Collapse
 

Preventative Maintenance - Brunswick All - Bearing Life

In relation to the recent “B Shaft” failure, I thought I would throw this subject on the table for discussion. I remember when I attended a “Bearing Life” seminar long...
 

Preventative Maintenance Brunswick A Jets A2 - SC/Dk Pulley Assembly

Found a bad left needle bearing in the Scissor / Deck Cable Assembly at the Rear Wall House. Needle Bearings are falling out and there is a pile of metal under it. Been 30+...
 

Preventative Maintenance - Brunswick B-10's Hollar House

Took a trip back in time to the classic “Hollar House”. The lanes went in in 1908. There was no ABC but according to the current operator, Tom, it became sanctioned when...
 

Table support assembly

My night at part job all 32 lanes going of leagues no where to move. Table support assembly broke rod broke # 2 Cell and bent the heck out of wire channel. Changed the Cell,...
 

Foul Light LED Mod

Here is a mod I came up with for a foul light unit. I was able to remove the old indicator light bulbs and replace them with ultra bright white LEDs. This should work for about...
Working...
X