AMF Pinspotters 82/70 Through XLi EDGE

Topics	Statistics	Last Post
Sticky: C1 Pinout drawing by PinCup Started by PinCup, 03-19-2011, 12:17 PM	25 responses 22,047 views 2 likes	Last Post by PinCup 10-07-2018, 10:41 AM
Sticky: The best tip you have gotten from Bowl-Tech by Mike Wilson Started by Mike Wilson, 02-04-2007, 12:39 AM	151 responses 106,749 views 0 likes	Last Post by Lee Christy 02-18-2015, 08:25 PM
Sticky: New Postings For Assistance by Kat Started by Kat, 04-30-2010, 11:30 PM	2 responses 10,404 views 0 likes	Last Post by Kat 05-03-2010, 11:32 AM
Counter balance spring tension by Carplop Started by Carplop, Today, 10:12 AM	1 response 3 views 0 likes	Last Post by Ausweegie Today, 10:20 AM
Rough table motion by albanybowlmech Started by albanybowlmech, 01-25-2019, 08:31 PM	12 responses 198 views 0 likes	Last Post by Pin_Head 02-15-2019, 09:42 PM
No spot after strike by 8270 Started by 8270, 02-10-2019, 02:45 PM	12 responses 184 views 0 likes	Last Post by AL 02-15-2019, 09:01 AM
Table wire removal by RobLogic Started by RobLogic, 01-18-2019, 06:41 PM	5 responses 155 views 0 likes	Last Post by Alastair 02-07-2019, 03:28 PM
c90 lower hub parts by drob1957 Started by drob1957, 01-07-2019, 05:00 PM	15 responses 182 views 0 likes	Last Post by Grit 02-07-2019, 09:16 AM
8270 Chassis by Rcole Started by Rcole, 01-31-2019, 03:45 PM	12 responses 152 views 0 likes	Last Post by mechanic8230 02-02-2019, 06:58 AM
Respot issue by lovetobowl Started by lovetobowl, 01-24-2019, 11:49 AM	8 responses 160 views 0 likes	Last Post by TheLegend 02-01-2019, 01:51 AM
82-70 Distributor not feeding 7 or 10 pins by catbowl Started by catbowl, 01-25-2019, 04:27 PM	4 responses 94 views 0 likes	Last Post by Alastair 02-01-2019, 01:47 AM
What is this? by Billcallen Started by Billcallen, 12-07-2018, 12:49 PM	8 responses 360 views 0 likes	Last Post by pitman2 01-26-2019, 11:06 AM
SS Chassis on power on table and sweep run by Akuma Started by Akuma, 01-07-2019, 12:51 PM	10 responses 158 views 0 likes	Last Post by pitman2 01-26-2019, 11:02 AM

Previous 1 2 3 4 11 51 101 501 879 template Next

No topics found.

Mark This Channel Read

Upgraded Motor Contactor

Hey all. Just had a motor contactor go on one of our machines. I remember seeing new cube relays or solid state contactors we could replace them with. Anybody got a part number...

C1 Pinout drawing

Finished the C1 drawing.

The base for this came from a drawing made by Felix dated 2006.

Thanks Felix.

If you see any...

CCD Processor Move by Masternut

These are pictures submitted by "MASTERNUT" of a project in his bowling center where he moved his CCD processor boards from the location on the capping to the curtain...

If you can not agree to any of these terms of use above or are not at least 18 years of age you are asked NOT to visit Bowl-Tech or utilize its content. To visit the Bowl-Tech Terms of Service and Rules CLICK HERE

Announcement

AMF Pinspotters 82/70 Through XLi EDGE

Tech for Hire

Adsense Featured 2

Upgraded Motor Contactor

C1 Pinout drawing

CCD Processor Move by Masternut

Adsense Classic 2