Initializing Tabs & loading Content...
-
Reply to Pinsetter Not Turn in On.Thank you for all Your Inputs Guys. Steve from Qubica Adjusted Camera Paremeters but still wasn’t getting the machine to turn on Patt, asked me to put two pieces of electric...Today, 12:34 PM -
-
Reply to Pinsetter Not Turn in On.Also, I don't remember when or where I heard this but, didn't Qubica have some problems with the switches on the side of the F-Box? I know the installers who put in our system...Today, 11:01 AM -
Reply to Pinsetter Not Turn in On.Have you tried giving your A&MC plug a wiggle? Could be a bad connection in there.
You can see if the problem is in the machine by unplugging the machine, then...Today, 10:43 AM -
Reply to Pinsetter Not Turn in On.Have you tried copying the pinsetter parameters from another pair?Today, 10:29 AM
-
Reply to Pinsetter Not Turn in On.For some reason, I had it in my mind that this is an MP chassis. However, we never established the chassis type. If this is an SS chassis, post back as we will need to make...Today, 10:16 AM
-
Reply to Pinsetter Not Turn in On.I put together this drawing for you showing the power control circuit for the 8270. This is only from what I can see from your pictures so you may need to verify the drawing....Today, 10:11 AM
-
When I'm faced with one of these I disconnect the deck and roll it out of the way. My back thanks me....Today, 01:22 AM -
Thanks Mickeygm. I will seek help from a bowling mechanic from a local alley. My thought, it’s ok to source the parts and puller now while I try and get someone to help. ...Yesterday, 06:47 PM
-
Reply to Pinsetter Not Turn in On.No red light neither on 11 or 12 that is turning on fine on the F box. Is that mean the problem has to do with the scoring?...Yesterday, 06:09 PM
-
Reply to Pinsetter Not Turn in On.I was double checking to see if I can see any cut wire in the A&MC box but nothing. I had
already checked them. And no red led on the odd lane side.
but I...Yesterday, 06:04 PM -
Reply to Pinsetter Not Turn in On.We seem to have lost you so I'm moving on for now. There are red LED's above the relays in the FBox. When you turn the scoring on for that lane, you should see one of the red...Yesterday, 05:59 PM
-
Reply to Pinsetter Not Turn in On.There appears to be a broken wire in the control wire as circled here. Can you confirm if that is broken all the way through?
...Yesterday, 04:36 PM -
Reply to Pinsetter Not Turn in On.Sorry is a mess.You do not have permission to view this gallery.
This gallery has 1 photos.Yesterday, 04:22 PM -
Reply to Asking for A2 HelpWhat you see in that procedure is the removal of the entire Deck assembly from the rest of the pinsetter in order to have adequate physical access to the sub-assemblies of the...Yesterday, 04:20 PM -
Reply to Pinsetter Not Turn in On.Can you take a pic of your wiring in the A&MC boxYesterday, 04:14 PM
-
Reply to Pinsetter Not Turn in On.Sorry that was my bad, I didn’t know the difference between the Jbox and A&MC box. When I tested voltage on my pins 5/6 on the A&MC box there is not voltage Present....You do not have permission to view this gallery.
This gallery has 1 photos.Yesterday, 03:59 PM -
Reply to Pinsetter Not Turn in On.If you remove the lower cover on the FBox, you will see this (see pic below). This is where the FBox terminals referenced earlier can be found. NOTE: This picture is of a Six...Yesterday, 03:51 PM
-
Reply to Pinsetter Not Turn in On.That's not the FBox. The FBox looks like this.
8270's don't use a J Box. Those are on 8230's.
The junction box you are showing is the...Yesterday, 03:43 PM -
Reply to Pinsetter Not Turn in On.Thanks for your input. I haven’t thought about that! Is it terminal 3/4 in the jbox cause
4 terminal terminals is emptied. The ones I have tested is 5/6 Manager Control...Yesterday, 03:32 PM -
Reply to Pinsetter Not Turn in On.You do not have permission to view this gallery.
This gallery has 1 photos.Yesterday, 03:26 PM -
Reply to Asking for A2 HelpI found this pdf on how to remove the moving deck, my question is, can a moving deck be removed even though I don't have any rods connected to the spring guide tube to relieve...Yesterday, 03:01 PM
-
A Loosed table Drive Assembly due to a loose bolt or worn out shaft drive key will cause that. Replace your table drive assembly key or if a new key fits loose you need to...Yesterday, 02:46 PM
-
Reply to Pinsetter Not Turn in On.Did you jump the power terminals in the FBox? Terminals 3 and 4 on Connector J3 or J4 depending if this is an odd or even lane. If the machine starts then it is a scoring issue....Yesterday, 02:33 PM
-
Reply to Pinsetter Not Turn in On.Not is not off, but I may consider to replace it even though I’ve never had one of those switches goes bad. Thank you for your input.Yesterday, 02:02 PM
-
Reply to Pinsetter Not Turn in On.Is the masking unit switch off? That will shut everything down.Yesterday, 01:59 PM
-
Reply to Asking for A2 HelpI checked the pulley and the cable was on. I was able to the bottom pulley on, but the turn buckle still doesn't want to move from it's position in the original photo that I posted....Yesterday, 01:22 PM
-
All cables, Deck And Scissor, must be removed and then the machine needs to be lowered to 270 to work on it. May want to get an experienced mechanic in to help with this. Before...Yesterday, 12:20 PM -
Hi Guys,
has any body have any Idea where else should I look for if Pinsetter is not turn on neither by the conqueror or the Toggle switch. I have done everything That I...Yesterday, 12:12 PM -
I just had one of these break on my Pinsetter # 1 at our club. It broke on the 12 pulley from the diagram.
This looks like it will take some doing....Yesterday, 10:25 AM -
I think it depends on which manual you look at. Also, sometimes they are shown on either the sweep shaft or table shaft but not both for clarity purposes so you made need to...Yesterday, 07:56 AM
-
Reply to Calling Sherlock Holmes
First year of the Automatic Pinsetter Engineers' Annual convention after the unveiling of the "Candle Light Contactor"
(depicted as CL-3 on your...Yesterday, 05:40 AM -
I have replaced the Lutco Bearing that my Table drive shaft passes through to get to the table drive assembly. During this process I have removed everything from the old table...You do not have permission to view this gallery.
This gallery has 2 photos.Yesterday, 04:49 AM -
Reply to Calling Sherlock HolmesThe model pictured has an adjustable auto timer shut off function. Was this covered in your apprenticeship or, was it on the job training?......Yesterday, 01:35 AM -
Reply to brunswick ball return parts...and he is correct. Those are the part numbers in question.
Even the Brunswick techs don't like those....02-03-2023, 05:07 PM -
Reply to Asking for A2 HelpOkay. Next question would be: is the lower cable still on the pulley at the rear of the deck?
We've already gone over how the upper deck cable is routed. The lower...02-03-2023, 04:58 PM -
Reply to Moving Machine 90XLThe rear pit wall doesn't look like it is interfering with any balls that would come the gutter on the opposite ball door side which is good news, so the buckled support doesn't...02-03-2023, 04:27 PM -
-
Reply to Asking for A2 HelpI got the cable on all of the pulleys except for the upper front pulley. When I tried to move the deck it wouldn't move, any ideas on how to fix?02-03-2023, 01:15 PM
-
No grease fittings on porkchops anymore. QAMF has removed them from many other assemblies too - all machine rod ends, spot/respot levers, shuttle brackets etc. Oil 'em up!02-03-2023, 11:14 AM
-
Originally, the oilite bushings were greased which is why it used that fitting. But oilite bushings really should't use thick grease because it clogs up the pores and prevents...02-03-2023, 10:32 AM
-
Reply to Zot Wizard Plus and Sync ScoringWhen you say it's on the +12V pin I assume you mean it's only on the left pin instead of the right pin as shown in the picture. It doesn't matter as it's only placed on one of...02-03-2023, 06:29 AM
-
The 3 letter supplier doesn’t exist as we know it, it’s now a 4 letter supplier. I’ve personally never put grease on the pins. You can buy self lubing bearings now....02-03-2023, 05:06 AM
-
I have bought a few new front roller brackets recently (Lamb Chops as they have been also known as within this site). They seem to be missing Alemite fittings or holes for Alemite...02-03-2023, 01:19 AM
-
Reply to A-2 turret issueHey mrdj you might want to check the Roller and bearing assembly part#12-150226-000 and make sure it is on correctly. The old Head Mechanic that used to work here didn't know...02-02-2023, 07:59 PM
-
Reply to Zot Wizard Plus and Sync ScoringThanks, exMech that pic I posted was a foul unit that is not being used I was using it just for reference the foul units out on the lanes are set to the correct voltage. And the...02-02-2023, 06:59 PM
-
Reply to brunswick ball return partsI think what he's referring to is those plastic caps that are fanned out over the ball rack rails that have the long reset buttons in them
I noticed in the 2011...02-02-2023, 06:56 PM -
Reply to Zot Wizard Plus and Sync ScoringHey Bowl-tech community,
Thanks for all of your info and help with this foul unit problem. I did get the foul units to register foul with the sync scoring system....02-02-2023, 06:43 PM -
Reply to Asking for A2 HelpCan be very difficult to explain without being in the machine with him, I agree.02-02-2023, 06:42 PM
-
Reply to The Future of OpenScore ScoringCurious if the raspberry pi project ever got completed? I was really looking forward to running this setup....02-02-2023, 06:08 PM -
Reply to Asking for A2 HelpAh, ye olde Deck Control Cable.
You'll notice the cable comes from the rear of the machine (that tube with the springs inside it), over the deck lift shaft, around...02-02-2023, 04:56 PM -
Reply to brunswick ball return partsThese numbers are out of the 2019 Service Parts Catalog
53-400097-xxx LH Exit Track
53-400099-xxx RH Exit Track
xxx = 000 Light Grey
xxx...02-02-2023, 02:57 PM -
Reply to Asking for A2 HelpSorry, I forgot to mention that I’m located in Austin, TX. Is there a specific way to put this cable on? Every time I try to put it on, it keeps unwinding itself off of the...02-02-2023, 02:43 PM
-
Reply to Okay I give upPrices look appropriate too according to the chart I saw on the Mm-C site.
This reminds me about our cushion linkage situation where I am. I have no idea how the...02-02-2023, 02:26 PM -
Reply to Okay I give upThose look quite sturdy compared to the Brunswick offering.02-02-2023, 01:33 PM
-
Reply to no communicationThis could very well be caused by your homerun box taking a dump. I've repaired two of these in the past week, it's a fairly common issue. PM me if you need info on getting it...02-02-2023, 12:34 PM -
Reply to Okay I give uppart numbers from McMaster...Hex Thread Adapters-91998A109, Ball Joint Rod Ends-60645K1202-02-2023, 09:16 AM
-
Reply to Okay I give upyou can get the turnbuckles and connectors from McMaster Carr.02-02-2023, 09:01 AM
-
I am currently looking to purchase a Gilmac bit for Turbo Switch Grips. Anyone have one laying around?02-02-2023, 08:56 AM
-
Reply to Calling Sherlock Holmes
 
Early light contactor from your apprenticeship years....02-02-2023, 03:16 AM -
hey guys.. we have frameworx ball returns in our center. I ordered 2 of the right and left hand exit track plastic pieces (where the balls come out of the powerlift). when the...02-01-2023, 06:13 PM
-
Reply to Moving Machine 90XLIt also looks like the urethane insert for the rear roller support weldment is missing. Replacing it will eliminate 5/16" - 3/8" of slack on that side of the carpet...02-01-2023, 04:25 PM
-
We recently purchased the Vector Plus system from a center. We are looking for someone who can help us track down the cabling and install it in one of our centers in northern...02-01-2023, 11:48 AM
-
Reply to A-2 turret issuemrdj is the problem solved ?, if not does the time delay spin properly when tripped? If spin is correct, clutch is good (as long as the turret rotates the first 9 pins with power)...02-01-2023, 11:11 AM -
Reply to Opening Back of 8290XLTheLegend greatly appreciate you taking the time to lay that out for me. Perfectly organized01-31-2023, 07:43 PM
-
Reply to Moving Machine 90XLHe might be looking at the why all the cross members are bent. Which basically sucks the two side frames closer to each other.
Which makes me believe when these...01-31-2023, 07:33 PM -
Reply to Opening Back of 8290XLYou start as you would rebuilding the pit.
Remove....
-- Pit cushion.
-- Front roller
-- Rear roller.
-- Carpet belt and bounce plate assembly....01-31-2023, 07:12 PM -
Reply to A-2 turret issueIf you look at the back of the torsion latch you will see a rubber bumper that stops the latch when it rotates back to its rest position to block the gear. You will see a groove...01-31-2023, 06:37 PM -
We have recently been having scoring issues with our AS90 scoring. I have gone thru the manual and followed the flow charts in the book to no avail, so I am looking for a service...01-31-2023, 03:01 PM
-
Reply to Okay I give upSame thing happened with me a long time ago LMAO!!! Lots of common organizational sense when it comes to the Brunswick manuals ya know (Not!)
01-31-2023, 02:32 PM -
Reply to Brunswick lane conditionerI think I'll try the "Super Clean" suggested above. $10 per gallon at WalMart. looks legit.
Do they make "Langlo" multi-purpose anymore? That's...01-31-2023, 01:12 PM -
Reply to Opening Back of 8290XLHaving worked on both the 8290 xl and the 8290 xli with edge upgrade, I prefer opening up the pinwheel for more space to work. With the 8290xl i would just take two of the bolts...01-31-2023, 11:32 AM
-
-
Reply to Brunswick lane conditionerMy guess is that lane cleaners and household cleaners like 409, Mr. Clean, Pine Sol etc. share a lot of the same types of chemicals/ingredients in them.
As far as...01-31-2023, 11:23 AM -
Reply to 2 way radiosI wear noise cancelling bluetooth headphones over my corded earpiece from the 2-way radio. Get to listen to my music, and protect my hearing in one go.
I don't like...01-31-2023, 11:11 AM -
-
I looked under Rake, Frame, and Pit Cushion. I cannot find the turnbuckle assembly that adjusts the mechanism which trips the shotgun on ball impact.01-31-2023, 09:15 AM
-
Reply to Wait times for pin ordersWe needed new pins about the time covid hit then we were shut down more than open and the money to buy them dried up. Fast forward to present day and we've been waiting since...01-30-2023, 06:54 PM
-
Reply to Brunswick lane conditionerI'm more worried about hurting the cleaner lines/pump/filter in the Kustodian.
I'm talking about a substitution as in not a proprietary sort of product. No supplier...01-30-2023, 05:34 PM -
Reply to Wait times for pin ordersI really don't know at this point man. I miss how strait forward this used to be. I don't even know how I can describe the pin situation where I am. We have circulated all the...01-30-2023, 05:24 PM
-
Reply to Brunswick lane conditionerCan you get Brunswick lane cleaners in your area? We have been using Invincible and it does an excellent job of stripping in our Envoy machine. In a strip only machine we used...01-30-2023, 03:44 PM
-
Reply to Brunswick lane conditionerCan anyone suggest a lane cleaner substitute?01-30-2023, 03:00 PM
-
Reply to Brunswick lane conditionerThe problem I'm having is getting lane cleaner (Moac). Haven't had any in weeks!01-30-2023, 02:59 PM
-
Reply to A22 stops mid cycleThat was it. Not sure why it just happened to fail completely right then after getting by for so long but it's good now. New 3rd gen sensor needed a slight adjustment to the sensitivity...01-30-2023, 02:32 PM -
Reply to A-2 turret issueOn a side note Quality makes some nice little alternatives on the x-pins at both ends of the short link.
12-1587 and 12-1588.01-30-2023, 02:14 PM -
Reply to Brunswick lane conditionerWe were using Connect but have Kegel lane oil coming from Buffa. Brunswick screwed up on this one because if our bowlers like the Kegel oil we will never go back to the big B...01-30-2023, 02:01 PM
-
Reply to no communicationTried thqt . No Luck. Going to try moving office CWC with another red in a little bit. Although I have already tried swapping out before with no success.01-30-2023, 12:43 PM
-
Reply to Setting empty deck after a strikeHad that M/D cam follower bearing go bad BUT i caught it during routine maintenance. Check long link too....01-30-2023, 11:03 AM
-
Reply to Worm shaft.A sister center had 2 of those greaseable parts,they broke. How long they we're in the machine i don't know but it was a P.I.T.A. getting part of it back out so that mechanic...01-30-2023, 10:59 AM
-
Reply to A22 stops mid cycleYes it does, on all lanes. And cleaning it was the first thing I tried.
I have a package arriving from Bob's Business today (our usual supplier) but for some reason...01-30-2023, 10:34 AM -
Reply to 2 way radiosI know this is an old topic but I have a modern solution. a center I reently encountered is using bluetooth headphones connected to the mechanic's cell phone. The desk simply...01-30-2023, 09:29 AM
-
Reply to Setting empty deck after a strikeIt is hard to tell in the picture, but the pin that holds the bearing in place actually wore out the holes in the frame allowing the bearing to really move around.01-30-2023, 07:22 AM
-
Reply to A22 stops mid cycleDoes this kick an error message? If so, does it do it on all lanes or just certain ones?01-30-2023, 06:36 AM
-
Reply to A22 stops mid cycleThe 2nd and 3rd generation sensors are optical sensors. They function kind of like infrared ball detectors or foul units. An infrared LED sends light out of the sensor which...01-30-2023, 06:35 AM
-
-
Reply to Worm shaft.20 lane Jap A2 centre closed down 15 years ago with original 1975 machines. 10 machines were purchased with the purpose of doing a reinstall. All 10 machines were deemed too...01-30-2023, 03:03 AM
-
-
Reply to Sprocket for table chainI know this is an older post. However the metal sprockets aren't a service parts listed/catalogued item. So we just counted the teeth and searched online for a metal sprocket...01-29-2023, 07:46 PM
-
Reply to Opening Back of 8290XLTheLegend just curious, what was your process for removing the frame? Have a couple at my center needing repair soon....01-29-2023, 06:42 PM
-
Reply to Opening Back of 8290XLReplacing a carpet on the XLI-Edge is a pita.
Have to take the pinwheel/elevator assembly out completely from our experience. Not fun, and we have to do a pit this week...01-29-2023, 06:40 PM -
The old place I worked said it took a year to finally get their B-max’s, and they were short shipped 19 cases.
Anyone else having significant delays getting pins?...01-29-2023, 05:44 PM -
Anyone know of any pro shop training courses? Drilling/plugging/sanding ect...
I found a course through Jayhawk in Kansas, and Kegel in Florida. Looking for something...01-29-2023, 05:20 PM -
Reply to A22 stops mid cycleThank you again. It was too loose. The cloth was raising when it should but then dropping as it started to return.
The eol sensor is a 2nd gen. The service manual...01-29-2023, 02:05 PM -
01-29-2023, 12:15 PM
-
Reply to no communicationCould be a unit down the line pulling down the system. Unplug J4 from the first unit and try it without the rest of the units. You may need to bring the terminator from the...01-29-2023, 10:49 AM
-
Reply to Table bounce during respotI can't even get a grease gun on most of mine that do have zerks. I just put a couple drops of oil on each side of the bearing. It works just fine.01-29-2023, 10:45 AM
-
Reply to Moving Machine 90XLI'm not sure I understand, which part has moved? If you're thinking of moving the whole back end, then you have to consider that you'll likely have to move the adjoining machine...01-29-2023, 10:33 AM
-
Reply to Setting empty deck after a strikeA long link issue or any of the components associated with stopping the machine at 180 could have been the issue. The key here was noticing the D shaft wasn't rotating. This...01-29-2023, 10:30 AM
-
Supertouch connects directly to the Hub and so it doesn't use L-Com. The fact you can get a game going on the scoring is a good indication the scoring is likely in good shape....01-29-2023, 10:23 AM
-
Reply to Zot Wizard Plus and Sync ScoringThe jumper on the Sync board should be right next to the connector for the foul lights. None the less, you can set the ZOT foul unit to work with whatever the Sync is set to...01-29-2023, 09:29 AM
-
Dealing with old installation of Accuscore with Accudesk, Wyse 185 front desk monitor.
Original monitor died. Replaced with new used unit. Fired right up and was able to...01-29-2023, 08:59 AM -
Reply to A22 stops mid cycleWhich generation of sensor do you have. It could be the sensor is fine and just needs adjustment. These are susceptible to temperature and humidity conditions as well as lane...01-29-2023, 08:30 AM
-
Call Daryl Tucker at Bowling Parts Inc.01-29-2023, 07:09 AM
-
A printable reinforcement for the end of PBWII to reduce the inevitable break at the first vertical support (short or not)....01-29-2023, 06:46 AM -
Reply to ZOT Quick Drop Rake issueCheck the Rake dashpot adjustment, aka the shock adjustment to make sure the Rake latch (shotgun) is locking at 90 degrees. Probably should check the entire Rake adjustment....01-29-2023, 01:51 AM
-
Reply to A22 stops mid cycleAm I right in thinking that the tension on the duster roll is what raises it? If so, could it be that I don't have enough tension on it yet?...01-28-2023, 09:32 PM
-
Reply to A-2 turret issueMight wanna take a closer look at the turret clutch a little more closely. This sounds to me like the friction disc is slipping instead of gripping since you cant feel any torque...01-28-2023, 09:23 PM
-
Reply to Setting empty deck after a strikeWas gonna mention that myself (well...180 interlock problems that is). Don't have to now....01-28-2023, 09:05 PM
-
Reply to Opening Back of 8290XLI find removing the pit cushion makes it easer for me to pull the bounce board out. And it's nice when the distributor is out of way too...that thing really does a number on my...01-28-2023, 08:36 PM
-
i had a sort of similar situation - turns out the wiring that going inside the carmera was loose and just had to tighten some set screws and all was well again...01-28-2023, 08:28 PM
-
Reply to Setting empty deck after a strikeGood job ma' man.
I have actually had the same symptoms happen to me in the past but all I had to do was file the gunk off of the face of the protrusion a little bit &...01-28-2023, 08:11 PM -
Reply to Setting empty deck after a strikeCouldn't this be as simple as a problem in the long link?01-28-2023, 08:08 PM
-
Reply to Asking for A2 HelpThe camcorder idea came to me years ago too. I just never went through with it, so thank you for reminding me! Maybe I'll actually make it happen at my center since we have a...01-28-2023, 08:03 PM
-
Yet another issue to add to the list.
A22 Authority - Changed the cloth this morning then tried oiling the lanes. It made it to the pit and then unraveled the new cloth...01-28-2023, 04:53 PM -
You said you copied the camera parameters but did you copy the machine parameters too?01-28-2023, 03:59 PM
-
Reply to Zot Wizard Plus and Sync ScoringWhere it says autoscoring on the foul units I would take a mutitester and put on pins when foul unit is activated see if the voltage is ac or dc and how much voltage there is,...01-28-2023, 03:33 PM
-
Hey guys I am looking for pin orientor pans! Does anyone have any or have a lead where to get? we have 82-30 pinsetters....01-28-2023, 02:22 PM
-
Reply to Setting empty deck after a strikeAll great answers. But have you ever seen a M/D follower this bad. I have never in 40 years seen one like this. It would touch and hold the M/D Scissor selector on the detector...01-28-2023, 01:14 PM
-
Reply to Brunswick lane conditionerWhat conditioner do you use? Classic has Absolute Control and Control in-stock. They are slightly overdue on Connect 2.0, by 1-4 weeks, so not sure when that will be available....01-28-2023, 01:09 PM
-
Reply to Zot Wizard Plus and Sync ScoringThanks for the input. Wookie8662 however, In the experience settings in Sync it is already set to score a foul. So, are you saying that the autoscoring plugs on the foul unit...01-28-2023, 12:11 PM
-
Reply to Asking for A2 HelpSomething else to LOOK at.....
Deck rollers (what the pins sit on inside the deck chutes-buckets)to see if they are swelled,not rotating freely when spun by hand.
...01-28-2023, 11:00 AM -
Reply to Moving Machine 90XLOh I was planning on cleaning up a little bit too. I’ve never had this pit out in 8 years. Lol01-28-2023, 10:11 AM
-
So I pulled out a carpet and bounce plate with the intention of replacing a front roller lambchop bearing and replace the carpet while I was at it. Been having an issue with a...You do not have permission to view this gallery.
This gallery has 5 photos.01-28-2023, 10:08 AM -
Reply to A-2 turret issueTension on the long turret drive belt, the latch is not releasing all the way when the time delay gear is pressing on the bell crank ( sometimes the bell crank has to much slop...01-28-2023, 07:29 AM
-
Reply to Synthetic approachesThe old ways are sometimes the best ways.
I mop our gutters & caps once a year with scalding hot water & a really small amount of our generic floor cleaner...01-28-2023, 12:20 AM -
Reply to Synthetic approachesThis brings me to another question that I never got around answering on my own.
Is there anything you guys know of that can fill gouges & scrapes on the synthetics...01-28-2023, 12:15 AM -
I have an a-2 that randomly won’t index past the five. The probe is hitting the torsion latch when the spider releases have installed new clutch disc time delay gear new turret...01-27-2023, 05:49 PM
-
Reply to Table bounce during respotWhile I was manually lowering the table I felt a little binding and heard a noise come from the 10 pin side of the table. I decided to check the table bearing (SR bearing). There...You do not have permission to view this gallery.
This gallery has 1 photos.01-27-2023, 05:42 PM -
Reply to Synthetic approachesI use to use windex on the slide area of the approach(the last 4-5 feet before the foul line), on the rest of the approach I used hot clean water and a dedicated mop head. I...01-27-2023, 05:12 PM
-
Reply to Problem with the interface box?If you are ready to start swapping parts, never use your spares. I'm going to assume for this example that the problem is on lanes 1 and 2. Swap one scoring component with lanes...01-27-2023, 04:59 PM -
Reply to Asking for A2 HelpAfter following the above advice it would be a good idea to make sure the upper deck cable and control cable are on their pulleys properly. Put a nearby pinsetter down to 270...01-27-2023, 04:35 PM
-
Have you tried changing out the LCOM box? Swap it with another pair and see what happens?...01-27-2023, 04:07 PM
-
Hello! Our center is in a bit of a jam.
We recently had a pair of lanes stop registering balls and scoring. I checked the camera and ball sensors and made the proper...01-27-2023, 02:55 PM -
Hello! Our center is in a bit of a jam.
We recently had a pair of lanes stop registering balls and scoring. I checked the camera and ball sensors and made the proper...01-27-2023, 02:54 PM -
Reply to Table bounce during respotI just had this happen and found the yoke weldment (I call it the clevis) off the table drive was not centered because the table drive was not tight and slid to the right causing...01-27-2023, 12:57 PM
-
Reply to Asking for A2 HelpNo. That isn't normal. There is a multitude of places within the deck assembly that can cause what you're seeing here (slacked out Moving Deck cable).
I can't tell...01-27-2023, 12:11 PM -
Reply to L and K questionsI remember the conversation for eliminating the table wiring. If I recall correctly, you only needed to purchase the XLMP to convert the scoring data into the necessary format...01-27-2023, 09:07 AM
-
Reply to Setting empty deck after a strikeThe problem is that the machine isn't stopping at 180 with an empty deck. You notice this more often with a strike because there is less time for pins to get to the turret and...01-27-2023, 08:22 AM
-
Reply to Zot Wizard Plus and Sync ScoringThere should be a jumper on the ZOT foul detector that allows you to set it to Brunswick or AMF. It doesn't matter which you choose but there is also a jumper on the Peripheral...01-27-2023, 06:34 AM
-
Reply to buffer brush questionsgot her back together...turns out most of the instructions match...maybe five that didn't...I think there is a speck too much crush on the roller, not much though...when I ran...01-27-2023, 02:03 AM
-
Reply to Table bounce during respotIt could also be caused by worn splines on the table drive shaft and/or gearbox. I've seen one so worn that it could slip a tooth when it wanted to.01-27-2023, 01:38 AM
-
Reply to Table bounce during respotIf it’s bouncing that much the keyway on the table shaft maybe be well worn. If not tighten the hell out of it01-27-2023, 01:10 AM
-
Reply to Asking for A2 HelpNo. Possibly a cable off the pulley.
Where are you located?...01-27-2023, 12:14 AM -
Reply to Vector +All I can dig up is this. Don't know how/if it might help you:
https://brunswickbowling.com/uploads...tallation-Manu...01-27-2023, 12:07 AM -
-
Reply to Asking for A2 HelpIs the trunbuckle supposed to be like this? If not how do I fix it...01-26-2023, 09:08 PM
-
Reply to Table bounce during respotThat's the first thing i'm going to check as soon as league is finished...01-26-2023, 08:06 PM
-
Reply to Zot Wizard Plus and Sync ScoringScoring system gets the foul signal from the foul lights, not the Zot unit.
Also, you need to setup the experience settings in Sync so that it will score a foul (it is ...01-26-2023, 07:48 PM -
Hello Bowl-Tech community,
I have the Zot Wizard Plus foul units for the Brunswick system. Does anybody know or have an idea to get them to work with sync scoring?...01-26-2023, 07:21 PM -
Reply to Setting empty deck after a strikeClarification: the spring rod coming out of the bottom of it could be binding on the bracket.
Check to make sure the x- pin didn't fall out where it attaches the...01-26-2023, 06:47 PM -
Reply to Table bounce during respotCheck that the table drive is tight on the shaft. I use our longest breaker bar to tighten down that bolt.01-26-2023, 06:35 PM
-
Lane 8 occasionally, during respot, will bounce on the way down to pick up the pins....as it bounce it triggers the OOR so now I have pins locked in respot cells.
Not exactly...01-26-2023, 06:20 PM -
-
-
Reply to Setting empty deck after a strikeCould be a blown follower bearing (tiny one) on the strike controller within the Detector.
For now, put the machine at 270 new pins & make sure that everything...01-26-2023, 01:15 PM -
Reply to Weirdness in moving deckIsn't it nice when you confirm you were right about the problem (or part of it) in the first place?
I'll bet though that if you weren't looking in the corners...01-26-2023, 12:56 PM -
Reply to Weirdness in moving deckDidn't see any obvious cracks. Got rid of the cable tube. Replaced the rear slides. Previous guy had them shimmed. Works perfectly now. Must have been the rubbing on the...01-26-2023, 10:52 AM
-
Reply to L and K questionsGood luck. My multimeter beep wasn't the loudest so it was a huge pain if the machines beside were running.
Hooking ours up was simple, phone cord normal end to...01-26-2023, 10:14 AM -
The machine A2 will set an empty deck more common after a strike than after a spare, but not always. The detector rod is dead on. It is like a hit or miss when it does it. The...01-26-2023, 09:20 AM
-
Reply to Synthetic approachesThe black "poop stains" that you come in & find across the approaches are from people bowling in their gym shoes. These are easy to remove with a small amount of...01-26-2023, 12:45 AM
-
Reply to Nexgen problemTry replacing the harness from the high voltage board to the CPU from another pair of lanes. Also if that isn't the issue check the fuses on the high voltage board.01-25-2023, 11:59 PM -
The problem with Nexgen.
cpu pcb
The LED next to F6 does not light up. What could be the problem?
The fuses are working, changed. The board is working,...01-25-2023, 11:05 PM -
Reply to Opening Back of 8290XLI agree with Alastair.
Opening the elevator requires unbolting the distributor support from the cross brace (which is easiest if you remove the distributor.) Then...01-25-2023, 10:12 PM -
North Florida church has a small bowling center with a Kegel Ion. Been without a head mechanic/lane man for a while. Have already contracted a mechanic to get machines up and...01-25-2023, 06:44 PM
-
Are there any Australian Centres looking to sell any Amflite II 2nd Hand pins to tie me over until the new stock arrives in OZ. I am looking for about 30 - 40 decent 2nd hand...01-25-2023, 06:40 PM
-
Reply to Opening Back of 8290XLOn the 90XL the pit comes out the front just like a 70 - you can try taking the pinwheel off, but by the time you've managed that utter palava, you can have the full pit assembly...01-25-2023, 04:48 PM
-
Reply to Synthetic approachesFor the hard to remove ball impact marks we use our water based lane cleaner in a spray bottle, a towel that is used only on the approaches and elbow grease. Finish off with the...01-25-2023, 03:51 PM
-
Reply to Synthetic approachesWe use a clean white or red pad on our high speed burnisher, and a spray bottle filled with isopropyl alcohol, ideally 90% or more so you're not leaving water marks behind. Do...01-25-2023, 03:28 PM
-
Reply to Which days do you have off work?Beautiful! I love cockatoos. Had an Umbrella when I was younger, but he was a rescue from an abusive home so I had to let a friend take him as she was better able to care for...01-25-2023, 03:14 PM
-
Reply to Opening Back of 8290XLWe do our 90XL pits with the pinwheel cover on. Also replace pinwheel belts from the distributor side, no need to remove anything other than the two bolts holding the distributor...01-25-2023, 03:11 PM
-
Reply to buffer brush questionsIt's identical...just the mechanic struggling...progress has been made...wanna call bs on the 20 minutes guy, but mine is a hairy mess...packed into the idler so bad it stopped...eventually...01-25-2023, 02:59 PM
-
Reply to L and K questionsI know I can change to camera for strikes, but don't have some comm related items, or knowledge of how to hook them up...I understand it's a challenge, but I would really like...01-25-2023, 02:55 PM
-
What is the best maintenance for synthetic approaches. I sweep and swab (mop) daily, still get the black marks and use a scotch brite sponge to get the tougher ones up. We have...01-25-2023, 02:25 PM
-
Reply to L and K questionsThankfully ours don't use the table wiring anymore so I don't have to worry about that because it was a huge headache even with only 2 wires on the respot switches....01-25-2023, 07:52 AM
-
Reply to Poll Suggestions?I was wondering the same, but this would vary greatly. A small GS center may literally only need 1 mechanic and front desk stuff who know how to pin chase, where larger centers...01-25-2023, 06:07 AM
-
Reply to buffer brush questionsGive the techs at Kegel a call. They can verify that you have the correct brush.01-25-2023, 04:52 AM -
phoenix s silver box...I have been having a blotchy looking oil application...based on research, it appears I need to change the buffer brush...so, I ordered one from classic...01-24-2023, 11:02 PM
-
Reply to Opening Back of 8290XLGalactic if you have the regular 90XL or XLi machines, the back cover is just held in by 4 bolts with spacers… you can do a pit job easily with or without the cover on. ...01-24-2023, 08:18 PM
-
Reply to Opening Back of 8290XLThe only backend I’ve seen this is the edge. But even to take it off is a bit of a pain. Depends on the version of pinwheel you have if it’s the 70’s style you’ve got...01-24-2023, 08:02 PM
-
Reply to L and K questionsI have a good drawing like yours...and I figured that's kinda how to go...all 8 of my machines are a rickety mess in this area...got one looking real good, but no luck and k...going...01-24-2023, 05:44 PM
-
Reply to A2 to GSXGSX will need new kickbacks, new ball return tracks, new pit area, maybe even different electrical.
If you want to convert, I would do the whole house at one time.
...01-24-2023, 03:12 PM -
Reply to Weirdness in moving deckI'll check for cracks TM when I have it out. Thanks.01-24-2023, 02:49 PM
-
Reply to Weirdness in moving deckI have found the cable tubes to present more hindrance than protection or "guidance" or protection of the Geneva pulley. They get dented & grind/bind. Of course...01-24-2023, 02:41 PM
-
The gearbox could be extremely loose. Have you tried swapping the complete motor to a different pair?01-24-2023, 01:50 PM
-
Reply to L and K questionsOk going to try to type this on my phone so if it's not the best sounding sorry.
I start at L wire and test into the contact in the table rail beside...01-24-2023, 01:49 PM -
Reply to A2 to GSXWhy do this in the first place?
Why complicate things?
I'm not a businessman, but when you look at this from a continued cost standpoint. I'd say it's...01-24-2023, 01:49 PM -
At the moment I'm exhausted and my brain is fried. I'm getting too old for this s%&#.
Machine that has been running fine all of a sudden acting up. I have an...01-24-2023, 01:45 PM -
Reply to Calling Sherlock HolmesDepending on the type of PU, they may undergo "Degradation" anywhere from 5 to 25 years. They basically "Revert" back to their original composition. Some...01-24-2023, 10:46 AM
-
The owner wants to buy a 10 lane center that has gsx to replace 10 of our 40 a2. How hard would it be? Do the gsx come out in one piece? Can we still use the same steal kick backs...01-24-2023, 09:29 AM
-
I have heard rumors that it is possible to easily open the back of a 8290XL. Apparently makes it easier to do a pit. Has anyone done this and do they have any photos or advice...01-24-2023, 05:42 AM
-
Check both chassis plugs (C2A) the top and larger bottom plug are in and secure. Try the pulling these out and back in trick to see if this resolves the issue.
Also check...01-24-2023, 05:00 AM -
Awesome! Those clutch assemblies are such fun to replace!
Glad you found the problem!...
01-24-2023, 04:53 AM -
Reply to Calling Sherlock HolmesI tend to agree. It has been my experience that most things these days are specifically manufactured for a short life span.
For instance, why does paint on modern...01-24-2023, 02:57 AM -
-
Reply to Calling Sherlock HolmesThe urethane recipe was changed so that we stay busy constantly replacing things. Steadys the cash flow. The ratio of ingredients in the urethane parts are most likely not the...01-23-2023, 06:46 PM
-
Reply to Poll Suggestions?Poll idea! Something I actually want to know. Does your center have 1 mechanic and several pinchasers? Or a mechanic on shift at all times?...01-23-2023, 05:52 AM
-
Is your table drive tight on the shaft? It needs to be absolutely tight or it will bounce the table01-23-2023, 04:15 AM
-
Reply to Calling Sherlock HolmesUrethane parts used to last forever. It seems they have a short lifespan now.
They sort of just start rotting and crumbling away.
Ive seen urethane pit mat covers...01-23-2023, 02:23 AM -
It's probably a foolish question to ask, but do any of you know for certain if a Vector Distribution board 5.0 can be used to replace a 6.0 Distribution board at all and/or without...01-23-2023, 12:36 AM
-
It's probably a foolish question to ask, but do any of you know for certain if a Vector Distribution board 5.0 can be used to replace a 6.0 Distribution board at all and/or without...01-23-2023, 12:26 AM
-
Reply to Calling Sherlock HolmesI'm lucky if anything at all that we get new last more than 10 days!! From Y-tracks to Time Delay Modules to Guide Rollers...you name it....01-22-2023, 11:21 PM
-
That is a centrifugal mechanism that contacts the start switches in the top of the bell end ....01-22-2023, 10:34 PM -
Reply to Not cycling issueWith all your help and doing the testing you suggested we followed the wire to a micro switch that we didn’t realize was there. We can not thank you enough. My dad was our mechanic...01-22-2023, 09:29 PM
-
Earlier this week we had a bearing on the shotgun of the quick drop rake break. It was causing the rake to drag across the deck, and not come up at the end of a cycle.
...01-22-2023, 05:35 PM -
Just reporting back that I've fixed the issue. While checking the belt tension I noticed the bottom wheel was moving a ton whenever a ball would go up the lift. Turns out the...01-22-2023, 05:04 PM
-
Reply to Calling Sherlock HolmesYou'll have to wait over 10 years to find out. They made a lot of crap back then as well, but that is all in landfills now....01-22-2023, 04:20 PM
-
hey guys...i have 5 machines with no strike cycle, and i am finally sick of telling customers to push the reset after strikes...so i am going in...first i confirm all wires are...01-22-2023, 03:10 PM
-
This was a time consuming problem (7 hours) to find so want to share--
Lane 10 would not score properly, intermittent and pin holders would not go vertical. Long story...01-22-2023, 08:04 AM -
Reply to Not cycling issueFor Accuscore plus, the switches get rewired in order to get the scoring to work on a Brunswick machine. There likely isn't a wire nut with 4 wires in it. The rear switch gets...01-22-2023, 06:32 AM
-
Reply to Machines not turning offThere could be a few different causes for this. It will depend on your chassis type.
This is most likely a stuck relay associated with the scoring. To eliminate...01-22-2023, 05:34 AM -
Reply to Calling Sherlock Holmes64! You got your money out of that one.
Do they even manufacture anything these days that will last more than 10 years?...01-22-2023, 02:31 AM -
Reply to Calling Sherlock HolmesTried to change the breaker in the panel box? I don´t know if that is the part you call breaker. Had a similar problem on my nr 5. When i opened the breaker it fell apart.Had...01-22-2023, 02:13 AM
-
Reply to Not cycling issueI was going to bring up what AL did here, but it's been so long since I worked with Accuscore that I couldn't remember it had the K1 relay (enclosed 'plug in' relay at the bottom...01-22-2023, 01:56 AM
-
Reply to Calling Sherlock HolmesCheck the power wires going from electrical box to channel to motor outlet and motor plug. Older wires get brittle insulation with hairline cracks which vibration can cause to...01-21-2023, 10:31 PM
-
-
Reply to Not cycling issueIf you have AccuScore Plus scoring you have tower switches and a K1 relay. Anything that cycles the machine will go through contacts 5 & 8 on K1. Check to make sure all wires...01-21-2023, 05:47 PM
-
Reply to GS pinsetter error code 1I would check the release lever adjustment that is to hit the gripper. I have had the adjustment screw loose and then it is too high and will not release the pin from the station....01-21-2023, 05:16 PM
-
Reply to Not cycling issueIt tripped when I put the voltage meter on 16 and 18 like you said. But got no voltage reading....01-21-2023, 03:40 PM
-
Reply to Not cycling issueHow did you go about cycling the machine? Did you break the IR beam for your triggering unit/scorer incorporated triggering, or did you drop the rake (closed the rake trigger...01-21-2023, 03:34 PM
-
Reply to Machines not turning offI'd make a post in the main 82-70 forum, you'll want to include chassis type as well as if its a common occurence. Only time i have that issue is if there is no pin in the 9 spot...01-21-2023, 03:09 PM
-
-
Reply to Not cycling issueI meant checking between 16 & 18, then after that, between 17 & 18 (in a hurry on typing on my smart phone during break at other job).
Take a look (within...01-21-2023, 02:46 PM -
I have 82-70s and amf accuscore plus scoring, last nite went to shut off machines from bowlers terminal and could not turn machines off I had to unplug machines to shut off. Any...01-21-2023, 10:51 AM
-
I'm looking for an Accuscore XL Back Office Manual. The owner where I work died and we don't have the manual for entering league scores and info. Thanks.01-21-2023, 07:53 AM
-
Reply to Not cycling issueJust out of curiosity has anyone checked to make sure that your ball detects are working properly?01-21-2023, 07:46 AM -
Reply to Not cycling issueIt could be a few different issues.
Start by taking a short jumper wire and briefly short TDM-16 and TDM-17 together. If the machine cycles, then you have a wiring...01-21-2023, 07:11 AM -
Reply to Intermittant Reverse SweepMight just need to replace the sweep reverse relay in it01-21-2023, 05:25 AM
-
-
Reply to Which days do you have off work?Well, sort of...LOL
My sorta kite, no running required and you don't even need a breeze.
1ft stainless wire connected to leg ring, so she can't chew...01-20-2023, 10:33 PM -
16 lane house, we are upgrading from the old spot/respot assembly with the hook and rod system to the carb link system. Trying to determine the type of material the old system...01-20-2023, 10:27 PM
-
Hi All, I have 90XL Silver Chassis and I have isolated an issue to the Chassis where the even lane intermittently does not reverse sweep after a first ball miss or if someone...01-20-2023, 09:20 PM
-
Reply to Not cycling issueGet a multimeter & set it to DC volts. Turn your pinsetter on & put one lead on 18 on the TDM and the other lead on 16 on the TDM. Do this with the wires still connected...01-20-2023, 09:14 PM
-
We have a lanes that doesn’t cycle. The rake comes down but we have to trip it every time. We also don’t have control of the reset buttons. After doing our research we thought...01-20-2023, 07:32 PM
-
Hi, my wife and I run a business where we organize large leagues in a relatively short time. I'd love to tell you more about it, email me at bowlingleagueguy at gmail.com.01-20-2023, 03:34 PM -
Reply to Ball ReturnsWow , will have to talk to my freind out there. He has no experience with these things but they did send him to school for them....01-20-2023, 02:53 PM
-
Reply to Which days do you have off work?Same with one of my ex-girlfreinds
!!...
01-20-2023, 01:42 PM -
Reply to Which days do you have off work?So you can fly her like a kite!??!! Awesome!...01-20-2023, 01:39 PM
-
Reply to Belts for Jetback Pulley?My intention is to use the Jetback Pulley 12-502410-000 on all my 8 machines. I have one new pulley and 4 used so that should work for the lot. 4 machines already runs with Jetback...01-20-2023, 12:38 PM
-
-
Reply to Belts for Jetback Pulley?What size pulleys do you have on the other machines? You can measure the diameter of the pulley to see what you have.
I use an A pulley on my A-2's as we sell...01-20-2023, 11:22 AM -
Reply to MP chassis PC card repair help.Hi.... I wrote you a private message if I can get your contact info. I know of a center in NY that would be interested in those MP chassis you have for sale listed in the classified...01-20-2023, 10:10 AM
-
Reply to Belts for Jetback Pulley?This is a solid style. Do you have 4 new pulleys?01-20-2023, 09:16 AM
-
Reply to Belts for Jetback Pulley?I guess you will call this the pivot style?You do not have permission to view this gallery.
This gallery has 1 photos.01-20-2023, 08:33 AM -
Brilliant idea. The ability to eliminate suspect circuits in complete safety....01-20-2023, 04:45 AM
-
Reply to Which days do you have off work?She is quite gentle when not protecting her nest. She has a leg ring that allows me to attach a string, which allows her free flight.
Before she paired up and started...01-20-2023, 04:31 AM -
-
Reply to Constant cycleSounds like a computer glitch rather than an electrical fault. Mr B is pretty clued on when it comes to Qubica trouble shooting.
The only thing that I can suggest...01-20-2023, 02:35 AM -
Reply to Moving deck cam follower.Possibly the 1:1 plate is has buckled forward creating the problem but, surely one would notice the follower not completely aligned the cam....01-20-2023, 01:00 AM
-
Reply to Moving deck cam follower.Steve Stafford has a picture of a drawing of the outline of the two different MDS cams on this site somewhere here.
From memory, the high dwell at zero on both...01-20-2023, 12:56 AM -
Reply to Constant cycleWhich lane computer do you have, usually between the monitors? Do you have Six boxes or F boxes on the curtain wall?
Reboot the lane computer for the pair with "erase...01-19-2023, 08:22 PM -
Reply to Belts for Jetback Pulley?Im guessing you have the solid motor mount shaft and not the pivot style.
So I cant help you out here.01-19-2023, 08:17 PM -
Reply to Belts for Jetback Pulley?For that pulley, my best combination has been A63 for M to GB and A92 for M to E. I order them online....01-19-2023, 06:05 PM
-
Reply to Pinball Wizard SwitchesFortunately that wasn't the case here. A simple switch replacement did the trick!...01-19-2023, 05:09 PM -
We operate two extremely busy bowling centers in the Northeast (Central Mass). We need to hire an experienced 8270 mechanic to work directly with our head mechanic. Excellent...01-19-2023, 12:42 PM
-
Reply to Belts for Jetback Pulley?My machines are American. 60 cycle. Original A machines that have been converted.
The motor to gearbox belt is 12-400329
The motor to elevator belt...01-19-2023, 12:27 PM -
I think i´m having the Jetback pulley on 4 of my pinsetter motors. My intention is to have the same pulley on each machine. As it is now 4 machines are faster than the rest,...01-19-2023, 11:58 AM
-
Reply to inventory timeIt's a little expensive, but Brainstorm Essentials has been a lifesaver. I haven't even gotten around to inputting our inventory (I think that'll end up being a summer project),...01-19-2023, 09:45 AM
-
Reply to inventory timeTook a look at the Parts Tracker website to read up on it. Nice n' straightforward. Thinking about implementing it.
But you're right, It would be an undertaking (borderline...01-19-2023, 07:06 AM -
Reply to Moving deck cam follower.This is what was occurring to me when I made my post...that maybe there's a difference in the machining of some MDSC's when it comes to serial number ranges or model conversions...01-19-2023, 06:27 AM
-
Reply to Constant cycleFirst check to make sure all the reflectors (on the capping opposite the camera assy) are aligned with their infrared & that they are without smudges & aren't cracked...01-18-2023, 06:58 PM
-
Reply to Poll - Ball Wheel StripsDoesn't outmatch the cost of your back & legs wearing out when you eventually have to remove that contact cement from the BW. I'll go with the more expensive ones with adhesive...01-18-2023, 06:38 PM
-
I don't know much about our scoring so I'll do my best here. We have a set of machines, lanes 19 and 20, that started doing weird things and it was because the cycle solenoid...01-18-2023, 06:04 PM
-
Reply to Moving deck cam follower.When I've had this happen to me, I have found that either the front interlock shaft is bent, or I simply modify the lever by grinding a new line in it. This moves the point of...01-18-2023, 06:04 PM
-
Reply to inventory timeYou could also ask QAMF for the full 70 parts list in excel and use this on a tablet as you work through counting all your items?
It's handy to put in place a minimum...01-18-2023, 03:46 PM -
Reply to HELP! Intermittent deck lightI swapped out the I/O just now. going to give that a try. I notice on the one i removed it was in a constant state of "on" possibly an issue with the cpu? not to sure...01-18-2023, 03:33 PM
-
Reply to Moving deck cam follower.OK is it a new cam on the 1:1, and is it the correct cam for your machines. There is two different cams, one for a scotch yoke 2:1 and one for a machine with drop link 2:1. And...01-18-2023, 03:27 PM
-
Reply to Poll - Ball Wheel StripsWe are using these foam kickers from bowlers supply. I was iffy with them when we first got them in because how could this hold up to abuse. Some of my 42 lanes still have the...01-18-2023, 03:05 PM
-
Thank you everyone for your help! It ended up being the relay after we took the 8 wires off the one and replaced it and solder the wires back on everything worked!!01-18-2023, 10:05 AM
-
Reply to What is itIt's been a while since I've experienced ball damage on my pair. My pin has been out-of-range for waaaay too long.
Lol....
01-18-2023, 12:05 AM -
Reply to MP chassis PC card repair help.If you are trying to reach Jon use this email address he does not get on Bowltech much anymore. wb8yjf@sbcglobal.net01-17-2023, 09:16 PM
-
Reply to Electrical helpThe end result of this was bad wiring. After changing the MSR and correcting some wires that were not in the right spots for a 208 system, the rapid firing of the MSR continued,...01-17-2023, 07:29 PM
-
Reply to MP chassis PC card repair help.I have a guy in Ohio that is very good and does us well01-17-2023, 05:34 PM
-
Reply to HELP! Intermittent deck lightsure its not the tombstone causing the problem i have tombstones that have been faulty had to replace them...01-17-2023, 03:35 PM
-
Reply to inventory timeIt's an undertaking for sure.... there are programs like Parts Tracker which can track your stock, orders, and stops etc... for everything not just machines.
When...01-17-2023, 03:17 PM -
Reply to What is itYeah, there's one on each side. The metal is the mounting bracket for the rubber.01-17-2023, 02:46 PM
-
Reply to What is itI think there's two of these in each lift. A left & a right (frameworx ball lifts). My memory might deceive me on this though. I remember seeing this issue when I worked for...01-17-2023, 02:38 PM
-
Reply to What is itThat is it! Thanks a million. It was missing from the ball lift I found it under and we have been experiencing ball damage on that pair.01-17-2023, 01:55 PM
-
Reply to What is itSounds like a "transition extrusion"
It goes at the opening of the ball lift on the side as the ball transfers to the rack. Item Groups Page 3F in the Blue Bo...01-17-2023, 01:18 PM -
Reply to Brunswick lane conditionerI'm in Ontario Canada and I just talked to my supplier near Toronto and he said he can't get any Brunswick conditioners now. Where are you guys getting your Brunswick conditioners...01-17-2023, 01:14 PM
-
That is centrifical switch...01-17-2023, 01:03 PM
-
-
-
This may require a photo also.
I found a broken one of these just in front of one of the ball lifts. I know that I have seen them before but I can't put my finger...01-17-2023, 12:57 PM -
Reply to Pin gate strap modificationSo basically you straightened it out & shimmed it centered with the middle of the pingate latch. This crossed my mind a lot but I just found myself saying "eff it"....01-17-2023, 12:41 PM
-
Reply to Brunswick lane conditionerYou can go with "Control". That's what we use. We never have a lane oil supply problem. Instead we're constantly running out of our lane cleaner ("Moac").01-17-2023, 12:35 PM
-
-
Reply to HELP! Intermittent deck lightHave you tried swapping the I/O and/or CPU to a known working lane to see if the problem moves?
I wouldn't think it would have anything to do with the pindeck lighting...01-17-2023, 12:00 PM -
This be the "brake" I was talking aboutYou do not have permission to view this gallery.
This gallery has 1 photos.01-17-2023, 11:41 AM -
Reply to Brunswick lane conditionerI use Brunswick control, and was told they would be out until Feb sometime.
Alot of our other houses have switched to Black Gold.
I would switch back to Kegel oil...01-17-2023, 11:00 AM -
We have been using Brunswick Connect conditioner but now we can't get it and Brunswick doesn't know when they will have it back. I called them and they said it was a raw material...01-17-2023, 10:17 AM
-
It is 8270 I only assume the mechanism on the gearbox shaft under the motor is a brake of some sorts. I worked for this house in 2016-2017 and moved states and worked at another...01-17-2023, 07:14 AM
-
Reply to Pinball Wizard SwitchesCorrect.
Most of the time for us the wire is pulled from the spade...and that's usually because the switch plate (PBWII v2) has loosened....01-17-2023, 07:08 AM -
Reply to Pin gate strap modificationI can't say I've ever heard of needing to bend the strap or link, only the gate.
Perhaps you could use a known good link, trace it and use it as a bend template...01-17-2023, 07:05 AM -
-
I have a spare 5 pin cannon plug with a jumper on the switch terminals and the other terminals insulated so they do nothing. It's painted a bright color and hangs on the wall...01-16-2023, 09:40 PM
-
Reply to Pinball Wizard SwitchesI replaced it with a generic switch. They're the same, but the blades are the small ones.01-16-2023, 08:15 PM
-
ive just noticed in the spare parts manual brunswick has made a mistake on the r/h table rack when threaded cap is put on they has to be a grub screw to hold it in place not a...01-16-2023, 08:14 PM
-
Reply to GS-98 Consolidated Box Power IssuesI see your post is 2 months old are you still having issues? i had a issue like that about 6 months ago. i may be able to help if needed still.01-16-2023, 07:47 PM
-
I have Gs-98 with consolidated box. I currently have 1 lane that the deck light turns on and off intermittently. we have upgraded to all LED lights in our units. I have replaced...01-16-2023, 07:12 PM
-
Probably an easy question, but are the microswitches on the motor assembly generic microswitches? I've got to replace one, and I've got a million generic switches.01-16-2023, 05:51 PM
-
20 Vector Touchscreens for sale. Also other related Vector Scoring parts available.
Contact Ron McKnight at Knob Hill Lanes 732-446-6001 after noon. Tues thru Saturday01-16-2023, 05:40 PM -
You mentioned replacing the brake. Can we assume this isn't an 8270 machine? What machine and chassis is this?01-16-2023, 05:13 PM
-
The ball light lamp has nothing to do with it. Good, bad or missing, the lamp makes no difference. The second ball signal comes from TS2-8 which is after the switch but before...01-16-2023, 05:06 PM
-
Reply to Electrical helpYou said this is a 220V machine but it is wired as a 208V machine. The first thing to do is check the voltage coming into the machine to verify it is a 220/230/240 V machine...01-16-2023, 04:21 PM
-
Problem solved!!!!! I swear I had continuity through the masking unit but I suppose I was wrong. In the picture is the back of the unit. You can clearly see where the line to...01-16-2023, 02:51 PM
-
This doesn't make the machine run any better. IMO it makes it easier to deal with.
Got tired of playing with the "bend it" strap adjustment. It isn't...01-16-2023, 02:37 PM -
Reply to Electrical helpAccording to the schematic I have H5 is taped.
On the low voltage side Yellow goes to the fuse holder through a connector to another wire.
Blue goes...01-16-2023, 02:23 PM -
I got called in to trouble shoot an electrical problem at another center. The MSR was not pulling all the way down. So I assumed bad relay. After swapping with for a brand new...01-16-2023, 01:57 PM
-
Did service work at a FEC center long ago with A-2's and Accuscore. They had issues...alot. One certain pair acted oddly...they changed this & that. Turned out to be the ball...01-16-2023, 11:03 AM
-
Here is a lousy drawing of our modified circuit. It is now clear why it works and bypasses the turret, deck, and masking unit switches and why the on/off switch still works....01-16-2023, 10:36 AM
-
We changed from Vector to BES-X Conqueror last year. When we've had no-scorer issues on a lane, it's because the lever for the second ball light switch is out of adjustment,...01-16-2023, 10:05 AM
-
Edit first line of my previous response to:
I have a similar problem that occurs with some regularity across my house.01-16-2023, 09:48 AM -
I have a similar problem that occwires leading to the start relay,urs with some regularity across my house. Here I run Zot motor start relays on both the combo motors. Consistantly...01-16-2023, 06:43 AM
-
I'm not familiar with your scoring system however, I do know that Qubica relies on the first and second ball light to signal to the computer system which cycle the machine is...01-15-2023, 11:48 PM
-
One thing to check is to make sure your table is stopping at 355. If it's trying to stop too soon it can run back down. It could also be a coasting gearbox. Nothing to do about...01-15-2023, 11:12 PM
-
We thought we had a scoring issue and at this point we are not sure. We have a pair that odd side scores and we have control of from keyboard and front desk. Even side does not...01-15-2023, 06:11 PM
-
I have a problem on lane 2. I have checked all wires every where and plug connections, tried using a spare chassis, replaced the table motor and capacitors under the black panel...01-15-2023, 02:33 PM
-
I'm not so sure. If my memory is correct, there was no thermal overload in the box. However, they also could be easily removed....01-15-2023, 10:43 AM
-
I have to admit, guilty as charged....01-15-2023, 06:28 AM
-
Those are replacement motors.
The original Toshiba motors with cast iron shells don't have one.
Red button on the motor or not, the pinsetter still runs...01-15-2023, 06:19 AM -
Unfortunately, this is also apparent in may centres here, in Australia.
How many centres have had a different computer scoring system installed over the last 30 years?...01-15-2023, 04:29 AM -
Yep. I agree,. The Jap made machines were/ are a lucky dip. Some are good, some are atrocious. The Jap manufacturerd A models were acceptable, the A2 models were just plain...01-15-2023, 04:18 AM
-
I commented on two posts in the thread. One was from Blister and the other Mr B. Neither was directed at you.
And, I further replied back to their comments twice...01-15-2023, 01:16 AM -
I've seen some horrendous bird nest boxes. I seen one centre of A2's that had the entire reset circuit on the curtain wall with only the wires to the solenoid going to the machine....01-15-2023, 12:40 AM
-
Then again, we are talking motors and they are easily interchangeable. The machines I speak of came from a closed centre in Japan, who knows if the motors were original....01-15-2023, 12:34 AM
-
Reply to Asking for A2 HelpThank you for all the responses and help. I'm slowly getting it little by little01-14-2023, 10:24 PM
-
STOP! STOP! STOP! STOP! SERIOUSLY PEOPLE!!!!!!!!!!!!!!!!
This post has nothing to do with someone's opinion as to whether or not someone thinks users should be allowed...01-14-2023, 06:49 PM -
If there is a J in front of the serial number all bets are off as to how it was made. I had a house with 4 Japanese A2, 8 converted A between 27,000 and 63,000, 12 American A2...01-14-2023, 05:25 PM
-
Reply to Xli Edge really that good???Generally these types of topics are on the edge pardon the pun....
What do you mean by good? What are you looking to compare the XLI Edge with? Are you looking to...01-14-2023, 04:17 PM -
Check the tension on the belt is good. You can adjust with the wheel at the top.
I would wipe down the wheels -(this should be a weekly PPM task) - You can have a...01-14-2023, 03:53 PM -
This is significantly apparent in the city of Chicago...01-14-2023, 02:00 PM
-
Has anyone had any experience in having their (pre-Brunswick) SES machines upgraded from the stock electronics to running with 360 Controllers?01-14-2023, 12:23 PM
-
Reply to GSX Consolidated board repair...To convert to NexGen, pretty much the entire electrical system gets replaced on the machine. Both the high/low voltage boxes get replaced in to 1 box, as well as new cabling...01-14-2023, 12:21 PM
-
Reply to A2 stops on standing cycleBeen doing this for a while now… not often come across things that didn’t make sense…. I got lane 1 sorted - did this intermittently- slightly shortened the spring that...01-14-2023, 11:30 AM -
Is there anybody outside of Brunswick that still repairs the GSX version of consolidated electronic boards? Brunswick no longer repairs them...also, I remember a "kit"...01-14-2023, 09:36 AM
-
My sentiments exactly!
The giving and following of electrical advice based on the assumption of the status quo is fraught with danger.
This is signifcantly...01-14-2023, 03:35 AM -
I've worked a house with 240 VAC Jap A models in the 50,000 range with thermal overloads on the motor....01-14-2023, 02:05 AM
-
Which wheels? Has anything else changed recently? Increase in lane oil volume? Change in type of oil used?
We have Brunswick Powerlifts, not AMF Profile, and have...01-13-2023, 06:58 PM -
Reply to Moving deck cam follower.I'll admit what I'm going to mention seems kind of ridiculous, but I don't think it's out of the question yet.
Could it be that the MDSC that is on this new 1:1 isn't...01-13-2023, 06:52 PM -
Reply to Brunswick Max LifePin feed issues like on the polycord?
Twisters are also pretty bad for OORs, but we’re lucky to have 1 OOR a week out of our 11 10-pin leagues. We use the Kegel...01-13-2023, 06:19 PM -
Reply to Moving deck cam follower.Double check your moving deck interlock adjustment.
There is a pretty strong spring on that blocking finger.
Only need to have the spring stretch about 1/16"...01-13-2023, 04:53 PM -
Profile - Ball - Return AMF 82-90XL PDF | PDF | Electrical Connector | Elevator (scribd.com)
Not an AMF guy, but I don't discriminate when I can help someone....01-13-2023, 03:58 PM -
Reply to Brunswick Max LifeAlright, so we've had them for about 10 days and our GS-X's have responded to them quite well. The dampers are a little dirty, however, so some pins are slipping out. Other than...01-13-2023, 03:06 PM
-
"We already know that the rear switch isn't wired to TS2-5 and TS2-6 like the drawing shows. So Mr. Blisters procedure to test it here won't work. As already explained, if...01-13-2023, 01:14 PM
-
Reply to Moving deck cam follower.Yes wookie I thought that was the culprit at first but still binding. Agreed head pin that's what has me stumped. Reasoning for me to believe the follower is coming to far foward...01-13-2023, 12:58 PM
-
Reply to Calling Sherlock HolmesYea. Looks like we'll have to wait until the next episode of Sherlock Holmes. huh....01-13-2023, 12:25 PM
-
Reply to Pinsetter is continuously re-settingIf you have electronic triggering, you can remove the trigger rod completely...01-13-2023, 10:47 AM
-
Reply to Xli Edge really that good???While in Vegas some time ago at Sams Town i stopped in to see the canter. WOW ! They got rid of the A-2 machines,put in AMF XLI (i think).It's been at least 8 years or more since...01-13-2023, 10:45 AM
-
Reply to Asking for A2 HelpI know on you tube there are videos of repairs etc. If i can find a certain one again i'll post it. The guy seems pretty good. Look up A-2 videos and you may find some.01-13-2023, 10:36 AM
-
Also, I forgot to include it, but you can test your deck jam switch as shown here. They make a special tool for it but you can rig up your own.
...01-13-2023, 09:00 AM -
We already know that the rear switch isn't wired to TS2-5 and TS2-6 like the drawing shows. So Mr. Blisters procedure to test it here won't work. As already explained, if it...01-13-2023, 08:52 AM
-
Reply to Pinsetter is continuously re-settingOh, and for on line training, I have never seen any online. I just dig into the manuals and go from there. I also read the posts here to glean any experience from all of you...01-13-2023, 08:28 AM
-
Reply to Pinsetter is continuously re-settingGuys, I was suspicious of it being mechanical. And it was. The Trip Rod was out of adjustment. The two bolts that are locked against each other had come loose. Took an hour...01-13-2023, 08:26 AM
-
Reply to Pinsetter is continuously re-settingMy guess, it's a mechanical fault. This is based on the assumption that the solenoid would have burnt itself out by now if it was an electrical fault.
There are...01-13-2023, 02:53 AM -
Reply to Moving deck cam follower.The forward motion of the cam follower is dictated by the high dwell of the MDSC. The cam follower is not adjustable unless you move the cam.
I tend to agree with...01-13-2023, 02:19 AM -
Not a reliable way is probably what you mean...and you would be correct.
Never assume these machines are wired the way they were all those years ago when they were...01-13-2023, 01:24 AM -
Reply to Moving deck cam follower.You probably have the clamping bolt backwards, as I have done that myself.
The nut and lockwasher should be towards the back of the machine, so only the bolt head is towards...01-12-2023, 10:13 PM -
Reply to Moving deck cam follower.Yes I understand that. The problem I am having is the the pulley an the pin where the flag contacts is coming to far foward causing the pin to put upward pressure on the shaft...01-12-2023, 09:14 PM
-
Reply to Moving deck cam follower.There's a little adjustable clamp-on bracket at the end of the blocking finger shaft that has a 1/4" bolt going through it. Get two 7/16 box end wrenches and run the pinsetter....01-12-2023, 08:44 PM
-
Ahh. Don't feel too bad. Sometimes, with me, a machine will pose a problem and after working on it for an hour or so, the whole time wracking my brain, I have a flash back of...01-12-2023, 08:14 PM
-
I have a pinsetter where the moving deck cam follower is coming too far foward on the machine causing the blocking finger shaft (triangle looking piece that lifts up blocking...01-12-2023, 07:43 PM
-
Looking for a couple zot time delay plus modules in working condition. Thanks let me know what your asking for them....You do not have permission to view this gallery.
This gallery has 1 photos.01-12-2023, 06:45 PM -
Thanks everyone when the FM came in Monday I wasn't here but he said it was a bent spoon causing the original issue. Which makes me feel dumb that i never noticed that! I didn't...01-12-2023, 06:29 PM -
Reply to Pinsetter is continuously re-settingYou should be able to unhook the Bowl Tronics from the pinsetter. You can unplug the 2 prong cannon plug at the top of the pinsetter electrical box to eliminate the bowlers reset...01-12-2023, 05:36 PM
-
Reply to Pinsetter is continuously re-settingI'm going to have to take another look at the pinsetter with it operating and see where it is when it's at zero. I'm guessing this is not mechanical, but I am pretty inexperienced...01-12-2023, 02:40 PM
-
Reply to Pinsetter is continuously re-settingHello from not too far away from you!
Gotta tell us a little more about your observations. Have you seen the way the GB linkage behaves while coming back around to...01-12-2023, 01:22 PM -
-
Reply to Asking for A2 HelpAnd while checking gearbox oil, check the moving deck cam follower shaft bolts. They need to be tight, and if turn a little, replaced, they are about to fail which can cause...01-12-2023, 11:55 AM -
Reply to Asking for A2 HelpThe dipstick goes in a full 11 inches so make sure not short stroking and over filling.01-12-2023, 11:18 AM
-
Hey guys, I was on here last year with failed bushings on the Control arm and you guys were great with your help. I have a new problem. Pinsetter Blogs of 4 is continuously resetting....01-12-2023, 11:11 AM
-
Reply to Asking for A2 HelpHave you checked the gearbox oil levels? Centered on top of the gearbox just in front of the reset solenoid is a spring loaded access cap. There is an after market dip stick...01-12-2023, 11:02 AM
-
Hello, first of all good work
Switch bowling machine Ku has a rear carpet shaft dislodged for some unknown reason and I don't know how it was installed. I will be glad if...01-12-2023, 02:16 AM -
Reply to Asking for A2 HelpWhat a change for you. Welcome to the Brunswick Field of Dreams. A couple term changes, the table is now moving deck. Moving deck has two levels, A) deck chutes, spotting fingers...01-11-2023, 11:21 PM
-
Reply to Asking for A2 Helpwith the ball accelerators popping off the small drive belt i would assume its the lge belt out of adjustment , accelarators not working could be a number of things relay a plug...01-11-2023, 08:42 PM
-
I’m working at a 16 lane house and need all the advice, videos or training that is available. I’m very familiar with the 82-70’s because I spent 13 years as a mechanic for...01-11-2023, 08:22 PM
-
The masking unit switch and turret jam switch are definitely bypassed on both machines. I'm not sure about the deck jam switch. I can't find a safe and easy way to do it but it's...01-11-2023, 08:20 PM
-
Reply to 82-70 Sweep EndsIf you are still looking for sweep ends. Feel free to call or text 518 728 3604 have about 10 lanes worth. Mike.01-11-2023, 01:28 PM
-
Reply to AMF Accuscore consoleAre you still looking for consoles and accuscore boards. I just pulled 16 lines worth. Feel free to give me a call or text at 518 728 3604. Mike.01-11-2023, 01:26 PM
-
Reply to XLMP AND EXPANDER BOARDSHey Joe are you still looking for expander boards? I have some. Feel free shoot me a text. 518 728 3604. Mike.01-11-2023, 01:24 PM
-
Have a problem on one of my pairs today with an AMF PROfile ball return. The ball comes up the lift, makes it half way up the first wheel, and starts to see-saw. The ball can't...01-11-2023, 01:00 PM
-
Reply to Calling Sherlock HolmesHad you done any work to the machine prior to this problem showing up? Could have been a wire in the wrong spot.
I wish the problem had shown itself rather than...01-11-2023, 07:50 AM -
Great photos.
Going through the photos, I can see somebody really worked over your machines. As you stated previously, this happened when the machine was running...01-11-2023, 07:19 AM -
Most of the time, sport bowling is like watching turtles high-five. The real sport bowling (in Chicagoland anyway) is actually late night weekend open bowl, where the real competition...01-11-2023, 05:39 AM
-
The only way I can watch Tenpin bowling on TV is to record and replay at twice the speed which mutes the sound and fast forwards all the tedious approach habits.
...01-11-2023, 01:51 AM -
2 belt brakes in 24 hours, and no spider release. Point me the direction of belts to tight. To add to what Mr Blister wrote about pulley belt damage. When the belts are to tight...01-10-2023, 02:16 PM
-
Reply to Time Delay Module capacitor failuresAt the bottom is a photo of the TDM readings I took last time I was in. This happened to come about coincidentally because when I got into work, I encountered an unresolved problem...01-10-2023, 01:08 PM
-
As I said, the production values of the crew when ABC and PBA were 'saner' made for great television. It was class...it was entertaining...it was a top-end show.
...01-10-2023, 11:50 AM -
Reply to Calling Sherlock HolmesThere has been a resolution however not an ideal one.
Removed all wires from the contactor. Didn't find any shorts. Flipped the breaker on. Nothing happened. ...01-10-2023, 11:49 AM -
Reply to Xli Edge really that good???Rbeard2012 The Edges have some great design features / upgrades from the previous AMF versions, but they aren’t built to take abuse from the entertainment / open bowling scene....01-10-2023, 06:47 AM
-
Reply to Front roller bracket spring boxHey Galactic, the table drive is on the end of the table shaft. I take it your now your the only tech in the venue that can help you? Have you had training before?
...01-10-2023, 06:13 AM -
Can anyone tell me what the name/type is for the cable (female end) connectors that land on the distribution board (Vector version 6). I know they're attempted to...01-10-2023, 05:48 AM -
Reply to Front roller bracket spring boxAny chance you can share a photo of what sounds like a fabulous invention. Im definately not a mechanic but own a small centre. Now forced to be a mechanic and this crash course...01-10-2023, 03:55 AM
-
I am still just using the jumpers on TS2 5 and 6. You can see it in the photos, it is the least dirty wire....01-09-2023, 07:08 PM
-
Reply to removing overtravel"TO ENSURE THAT ANYONE WITH COMMON SENSE IS HINDERED BY UNNECESSARY REGULATIONS, AND THAT THE AWARE AND INTELLIGENT BE PERPETUALLY ADHERENT TO THE DICTATES WHILE THE LOWEST...01-09-2023, 06:46 PM
-
Spelling correction: ..."You describe what seems like instantial intermittent conductivity issues"...01-09-2023, 04:34 PM
-
I'd love to help you out but at this point it's starting to feel like a bad game of 20 questions. In order for us to be able to help you, you have to help us. Please post some...01-09-2023, 01:46 PM
-
Here's a couple more odd things. Check the halo ring. Poor adjustment or getting bent down can apply pressure to pins pressing down on spoons. Also have seen a very tight connection...01-09-2023, 01:18 PM
-
Why not just open the bottom of the wire channel & do continuity tests for each wire running through it at this point. Sure, it's tedious but this might be what you have to...01-09-2023, 12:01 PM
-
Don't get me wrong, it's damn cool sometimes to see a pro throwing crushing strike (incomparably better in real life when I happen to be up front during a tournament & watched...01-09-2023, 11:52 AM
-
Reply to A2 stops on standing cycleIt's what we're here for (at least for the most part). It's very satisfying when we can pass knowledge onto someone while at the same time, that person is applying their own initiative...01-09-2023, 11:26 AM
-
That is a strange coincidence, but at the same time it's not at all unusual. You have to compare the condition of these two snapped belts 1st off to see if they don't share the...01-09-2023, 11:11 AM
-
Wow...like a contestant on Hollywood Squares after hearing a bluff answer, I have to disagree.
ABC's coverage of the PBA's Pro Bowlers Tour was right on the mark!...01-09-2023, 10:46 AM -
Reply to 82-70 table and cradleThat was the fix, when i checked the springs before they seemed tight, took the cup off and loosened the bolt to see that it was installed loosely. Thanks for the catch....01-09-2023, 09:11 AM
-
Reply to A2 stops on standing cycleThanks for your replies…
I replaced the reset lever and it now runs fine…
they must stretch or fatigue- anyway all is well again
...01-09-2023, 04:48 AM -
Hello I'm a brusnwick certified gsx mechanic. I have close to 2 years of experience working on these machines. Looking to relocate soon. I have a lot of knowledge on these machines...01-08-2023, 11:55 PM
-
Thanks for all the input! some things mentioned i have already checked. But a few i havent. Im gonna look further after league tonight. Last night was a crazy saturday night and...01-08-2023, 08:03 PM
-
Sparkplug your problem of "drop the 5 but not the other 9" has dozens of possibilities that are all correct. Kanga and Mr. blister have giving you some good ones, But...01-08-2023, 05:12 PM
-
If you don't have time delay modules you should have relays that replace them. You can do that with Qubica scoring. Do you have something to the left (as you look at it) of the...01-08-2023, 05:00 PM
-
Reply to A2 stops on standing cycleI have some about 20,000 serial number with a really strong double sided reset lever. They are still just as strong and reliable after they are modified to eliminate the obsolete...01-08-2023, 04:55 PM
-
We do not have that relay and I'm almost certain we do not have time delay modules...01-08-2023, 04:47 PM
-
01-08-2023, 04:46 PM
-
Reply to Ball ReturnsYou should be able to come close to no pins ever entering the doors, but as already pointed out there is alot of adjustments to get right. It should also be noted it can be hard...01-08-2023, 06:43 AM
-
Reply to Machine Cycle Suspension1. I already changed the motherboard from the stock nexgen and the problem persists.
2. The problem does not occur on the adjacent lanes, these are lanes 1 and 3.
...01-08-2023, 06:06 AM -
Sometimes it's just time and the wear & tear that comes with it.
If you don't have the sort of crooked pin jams mentioned above by Kanga, what you're dealing...01-08-2023, 02:05 AM -
Reply to A2 stops on standing cycleI can't argue with that. It'd be great to have one less concern on your mind when the front counter calls and says, "I need a reset on lane #..." or "lane #......01-08-2023, 01:38 AM
-
I accidentally put this post in this thread. It belongs in a different one where someone is having strictly a motor/pin light issue & his contactor won't energize at all....01-08-2023, 01:22 AM
-
The ability to refrain from reaching out and choking the living life out of an abnoxious customer whilst smiling and being courteous is a trait that many do not have but, is highly...01-08-2023, 01:14 AM
-
Reply to Time Delay Module capacitor failuresThank you! I don't know WTF is wrong with me lately. Used to have most of the knowledge described in your post at the front of my mind. Forgot a lot being away from the bowling...01-08-2023, 12:38 AM
-
Reply to A2 stops on standing cycleShould have read single piece reset lever but you picked it up.
Not so much how the mech works but, rather the design and material used to manufacture it.
Not...01-08-2023, 12:00 AM -
Typically it's the result of a bent (spread) turret wire allowing a pin to sit at an angle and the base of the pin will hold the spider locked... or a halo that 's clamped too...01-07-2023, 09:55 PM
-
A-2 - Lane 1 will randomly drop the 5 but not the other 9. I will pull turret backwards just slightly and the other 9 drop and its runs. Do i just need to change clutch? I have...01-07-2023, 08:17 PM
-
Reply to Ball ReturnsYou said, "Also I notice how fast the machine comes down on 1st ball standing pins." I assume you mean how fast the setting table moves going up and down, not how ...01-07-2023, 07:41 PM
-
Reply to 82-70 table and cradleI actually lengthened the two rods on the back (two full turns on the top rod end), no notes left and watched it for two shifts of youth bowling today, so that seems to have fixed...01-07-2023, 05:53 PM
-
Reply to Ball ReturnsIt certainly wouldn't help, but I would suspect there is far more to the issue than the machine cycling quicker than expected....01-07-2023, 05:47 PM
-
Reply to Ball ReturnsThere are many things that could cause issues with pins getting in the ball accelerator. Cushion isn't adjusted in the right position, the t-band tension is too loose, the t-band...01-07-2023, 05:46 PM
-
Reply to Ball ReturnsExcept the sweep running sooner puts more pins in the pit quicker and a build up of pins may not be allowing them to clear before the ball door unlocks.01-07-2023, 05:37 PM
-
A thermal overload here would prevent the contactor from energizing but would not prevent the MSR from energizing so it isn't really an issue.01-07-2023, 05:34 PM
-
Reply to Time Delay Module capacitor failuresYou've asked a lot of questions here. I'm not sure we'll get all your questions answered but let's try to get a few.
"I want to get to the bottom of why these...01-07-2023, 05:30 PM -
Reply to Ball ReturnsThe ball door is on a set timer to keep the ball door locked, so the machine cycling earlier shouldn't be a huge deal....01-07-2023, 05:15 PM
-
I apologize for the possibly mis-informing description I made. My mind breaks down & processes things in a way where I describe them portionally simplified. I was descibing...01-07-2023, 04:52 PM
-
Reply to Lane helpThat's a pretty vague question. So first, we've got to ask more determinable questions because nowadays there are all sorts of different formulas for different bowling condit...01-07-2023, 04:18 PM
-
Reply to Ball ReturnsThe time is 3 seconds.
Both problems could be related. The ball door has a time delay to allow pins time to clear before opening. If the machine triggers...01-07-2023, 02:54 PM -
In the lower right corner of the electrical box (low voltage side) do you have an extra relay like in this picture? (item 4)
And/or does...01-07-2023, 02:41 PM -
Reply to A2 stops on standing cycleInteresting take because from what it looks like to me, the model A's (it looks like especially the earliest models) have a considerably more complicated Reset Lever assembly...01-07-2023, 02:40 PM
-
Hi, I iwas just curious, I have recently gotten back into bowling and our old place that has been reinvented as the last production model GS's. I am curious why our league bowlers...01-07-2023, 02:26 PM
-
Reply to Machine Cycle SuspensionI was onboard with this, for the first paragraph at least.
There very well could be other issues at play here, but I wouldn't check anything with the table, as the...01-07-2023, 02:24 PM -
Reply to NexGen CPU questionI know it's a hassle, but have you swapped the boards with a pair of lanes that are known to be working, to see if the issue moves or stays?...01-07-2023, 02:15 PM
-
Reply to Machine Cycle SuspensionWith the information you gave us, I would check the adjustment of the ball detect sensor. The pinsetter is not throwing a code which means that the ball detect’s beam is not...01-07-2023, 12:52 PM
-
Hello,
for some time I have been encountering a problem on Brunswick GSX machines with which I do not know how to deal with because until today I have not discovered...01-07-2023, 12:41 PM -
I tried working the counter at my center. I had such a hard time with "people skills" (and memory problems when it came to being trained about how all these different...01-07-2023, 12:17 PM
-
Reply to A2 stops on standing cycleThey're not a problem for me unless somehow the arms of the 2-yoke Reset Lever are bent inward toward each other too much. There was one time I found one hanging on the wall that...01-07-2023, 11:39 AM
-
Reply to 82-70 table and cradleAs far as the hesitation in the cup rotation, that could be as easy as a slight adjustment to your yoke springs. Increase the tension slightly and see if it smooths out. Although,...01-07-2023, 10:11 AM
-
Reply to Ball Cushion Frame - BrokenI might be slapping myself on the back of my head, but I wonder which ball cushion stop bracket mounting holes will last longer, the kickback or the accelerator housing?01-07-2023, 09:20 AM
-
Update: I don't know what happened or what changed but I tried my jumper again and the contactor energized and stayed on. So I put everything back together and the rear on/off...01-07-2023, 08:44 AM
-
I have wood lanes and a DBA Phoenix lane machine.what type of lane conditioner do I use?01-07-2023, 07:15 AM
-
Reply to A2 stops on standing cycleTwo part reset lever = problems.
Another unwanted and unneeded modification from the A model.01-07-2023, 06:09 AM -
Reply to Ball Cushion Frame - BrokenEverything you said in this comment makes so much sense. Yes both of our that have broken were on the "non-hydraulic" side.
Time to do some custom modification....01-07-2023, 05:50 AM -
Reply to Xli Edge really that good???Any machine is only as good as it’s looked after. The latest machine is the Edge Freefall (rebranded XLI) I’ve got no idea what the difference is. The edge backend does eliminate...01-07-2023, 05:37 AM
-
Tenpin bowling is terrible spectator sport.
How anyone can sit through a televised game is beyond me. It's incredibly boring and mundane.
The competitors...01-07-2023, 04:17 AM -
They have been trying to engage the young people into Tenpin bowling from an early age in my country for as long as I know, it has not been a success.
Tenpin bowling...01-07-2023, 03:19 AM -
Reply to A2 stops on standing cycle**errors on my part:
I meant clockwise.
Forgot about the pin at the front of the plunger lever that comes through the actuator....01-07-2023, 12:26 AM -
Since it's not a contact sport, it isn't as important (from a biological and then cultural standpoint). It's indirectly competitive, which bores spectators. Contact sports are...01-06-2023, 06:59 PM
-
i often wonder where bowling would be this day in time if it had been promoted/embedded into us(at a young age) like basketball, football, baseball, soccer ect....01-06-2023, 05:51 PM
-
Reply to Calling Sherlock HolmesThose old contactors still work. You can't buy parts for them or new replacements because the company made okay stuff for a long time and then suddenly started making stuff so...01-06-2023, 04:04 PM
-
Reply to Ball Cushion Frame - BrokenI have only seen this at our off-base/local bowling center, the the less beefier frames for the older GS model(s). I'm not sure if inside and/or outside climate conditions will...01-06-2023, 03:28 PM
-
Reply to Calling Sherlock HolmesMessages received. Thank you for all the help. Still working on it. Will post back.01-06-2023, 02:02 PM
