No announcement yet.

Cost of flat screen scorning monitors for Accu-Score system


Adsense Classic 1



  • Filter
  • Time
  • Show
Clear All
new posts

  • Cost of flat screen scorning monitors for Accu-Score system

    I need an estimate for the cost of flat screen monitors. I was told I need to come up with this info but I don't have any idea where to look, nor do I have any suppliers price lists.

    What's the cost of these things. Only need 6 (6 lanes in the center).

    New price / used price?

    What to look for, where to buy these things? Who installs them etc?

  • #2
    Sent you a PM.

    We leave our greatest mark on this earth with the quality of our craftsmanship.


    • #3
      Thanks for the PM. I did not know you could buy monitors from your local big box store and use them. I thought they had to be some kind of special hook up for the scoring unit. That will be helpful in getting a price quote.


      • #4
        Depends on the type of Accuscore system...although you can still buy the monitors from the big box store. If you have Accuscore +, you will need an adapter to convert the signal to something the monitor can understand. If you have Accuscore XL...the monitors will work right out of the box.
        TSM & TSM Training Development
        Main Event Entertainment
        480-620-6758 for help or information


        • #5
          What if I have regular accuscore??


          • #6
            Accuscore I, Accuscore II, Accuscore + and finally Accuscore XL.

            Which version do you have? Do you have a picture of the CWC? That might help us determine what you have and what you would need.

            I am not sure of what you would need with I and II...but I know you would still need a converter...just not sure which you would need.
            TSM & TSM Training Development
            Main Event Entertainment
            480-620-6758 for help or information


            • #7
              Looking for the same info. What converter do I need for accuscore plus? The current monitors are 27" Zeniths and they are slowly dying. I haven't been in this long enough to know much about the monitors. Also, who can I turn to for main computer problems? My CWC behind the main desk is dead. I switched it with one from the lanes and the EPROM is good. I do have one spare, but it has no communication. Any help is greatly appreciated. For now I'm stuck in stand alone.


              • #8
                Besides the PM, you should only be stuck in stand alone on one pair. There are folks who repair them. WB8YJF service is one. He is here on BT.
                This post is not an unpaid promotion of my business.


                Topic Starter RibbonScript


                Adsense Classic 2

                widgetinstance 666 (Related Topics) skipped due to lack of content & hide_module_if_empty option.

                MP Chassis Tester

                Good morning,
                I have built a tester for the MP Chassis for the 82-70 machines. Instead of using the cam switches
                I am using relays. My question is to anyone that may...

                Preventative Maintenance - As, Jets, A2s - LEDs

                Those of you looking for new LED lighting ideas may want to check out this site. Lots of stuff.


                4:1 Timing off..

                *sigh* Hello friends..

                I had a 4:1 go bad and I've never seen or done one before. Trying to search the depths of the forums, YouTube videos, it didn't seem too bad....

                Adapting the Bluffton end cap & terminal board kit to Franklin BE (and FE) motors.

                Left a rant about this in the bowling forum…

                I’ve already repaired a a number of Franklin FE motors using the Bluffton-style end cap and terminal board kit (090-004-582)....

                Turret clutch rebuild

                At what thickness do you replace the clutch face.
                Is there a minimum dimension from the clutch face to the rivet.


                Solderless relay conversion

                Is anyone running the solderless relays on the accelerators? How do you like them? What brand? How difficult to convert was it? Would love the feed back as I'm about to switch...