Announcement

Collapse
No announcement yet.

New one on me!

Collapse

Adsense Classic 1

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • New one on me!

    Lane 13 would not set pins.

    After the machine cycled...the sweep would go to guard....read a X....then run through and go to 0.

    Upon inspection the table switch cam had slid to the right rendering the switches useless.

    I have never seen this in 20 years.

    All the other cams and cam followers were lined up and the cam stud was tight.

    JK

  • #2
    Re: New one on me!

    Jk; the only time, and alot of times; I strip the stud when adjusting, but I can't remember a time when the cam came loose! :p Please Don't use the Torque wrench on this one. [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
    If at first you don't succeed, try, try, again. Then quit. There's no use being a damn fool about it." -W.C.Fields

    Comment


    • #3
      Re: New one on me!

      Originally posted by felix:
      Jk; the only time, and alot of times; I strip the stud when adjusting, but I can't remember a time when the cam came loose! :p Please Don't use the Torque wrench on this one. [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
      <font size="2" face="Verdana, Helvetica, sans-serif">The stud was not loose or srtipped....and the employees last night can not distinguish a monkey wrench from a combo wrench.

      JK

      Comment


      • #4
        Re: New one on me!

        Originally posted by 82/70 king:
        </font><blockquote><font size="1" face="Verdana, Helvetica, sans-serif">quote:</font><hr /><font size="2" face="Verdana, Helvetica, sans-serif">Originally posted by felix:
        Jk; the only time, and alot of times; I strip the stud when adjusting, but I can't remember a time when the cam came loose! :p Please Don't use the Torque wrench on this one. [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
        <font size="2" face="Verdana, Helvetica, sans-serif">The stud was not loose or srtipped....and the employees last night can not distinguish a monkey wrench from a combo wrench.

        JK
        </font><hr /></blockquote><font size="2" face="Verdana, Helvetica, sans-serif">I Can't either ; Did the motor shaft move? [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/confused.gif[/img] And Yes It Can! [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] Ya wanna cookie?
        If at first you don't succeed, try, try, again. Then quit. There's no use being a damn fool about it.&quot; -W.C.Fields

        Comment


        • #5
          Re: New one on me!

          Originally posted by felix:
          </font><blockquote><font size="1" face="Verdana, Helvetica, sans-serif">quote:</font><hr /><font size="2" face="Verdana, Helvetica, sans-serif">Originally posted by 82/70 king:
          </font><blockquote><font size="1" face="Verdana, Helvetica, sans-serif">quote:</font><hr /><font size="2" face="Verdana, Helvetica, sans-serif">Originally posted by felix:
          Jk; the only time, and alot of times; I strip the stud when adjusting, but I can't remember a time when the cam came loose! :p Please Don't use the Torque wrench on this one. [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
          <font size="2" face="Verdana, Helvetica, sans-serif">The stud was not loose or srtipped....and the employees last night can not distinguish a monkey wrench from a combo wrench.

          JK
          </font><hr /></blockquote><font size="2" face="Verdana, Helvetica, sans-serif">I Can't either ; Did the motor shaft move? [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/confused.gif[/img] And Yes It Can! [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] Ya wanna cookie?
          </font><hr /></blockquote><font size="2" face="Verdana, Helvetica, sans-serif">Fudge stripe please.

          JK

          Comment


          • #6
            Re: New one on me!



            Fudge Stripe?? Myself I perfer pink! [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
            If at first you don't succeed, try, try, again. Then quit. There's no use being a damn fool about it.&quot; -W.C.Fields

            Comment


            • #7
              Re: New one on me!

              Been there....done that....those were the good old days.

              JK

              Comment


              • #8
                Re: New one on me!

                Good Ole Days' Smoke &amp; Drink...and No Spitters.. [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
                If at first you don't succeed, try, try, again. Then quit. There's no use being a damn fool about it.&quot; -W.C.Fields

                Comment


                • #9
                  Re: New one on me!



                  mAGIC t???
                  If at first you don't succeed, try, try, again. Then quit. There's no use being a damn fool about it.&quot; -W.C.Fields

                  Comment


                  • #10
                    Re: New one on me!

                    [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]

                    chad................quella....................
                    If at first you don't succeed, try, try, again. Then quit. There's no use being a damn fool about it.&quot; -W.C.Fields

                    Comment


                    • #11
                      Re: New one on me!

                      What!?!?
                      Yes, I remember each of them briefly working in the snack bar. Occasionally, I'll still run into them at the bar down the street.
                      If you want any other details, well, a gentleman never kisses and tells...
                      What was this thread about? Oh yeah, cams.

                      When I went to Stahl's school, a lot of troubleshooting was focused on correcting someone else's sloppy work (terminals not quite connected, etc). Today, troubleshooting scoring problems, I've found I need to start at the most basic possibility for the cause of the problem. This cam placement thing is a perfect example.
                      Checking voltages etc wont do you a dern bit of good if the rollers aren't riding on the cams!

                      The Quellinator

                      Comment


                      • #12
                        Re: New one on me!

                        Originally posted by felix:
                        [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]

                        <font size="2" face="Verdana, Helvetica, sans-serif">...I Like flowers...
                        "Where are we going, and why are we in a hand basket?"

                        --Kat

                        Comment

                        Topic Starter RibbonScript

                        Collapse

                        Adsense Classic 2

                        Collapse
                        widgetinstance 666 (Related Topics) skipped due to lack of content & hide_module_if_empty option.
                         

                        Rake sweeping out of time, and pin launching onto lane.

                        I work on some nice old Brunswick A-2 pin setters. Most issues I've come across haven't been to problematic to figure out. But being I can't seem to get it to recreate the issue...
                         

                        Strange sweep problem

                        I’m a rookie mechanic and have been working on pinsetters for 2 years. One of my lanes has a problem with a sweep possibly coasting. I don’t know what could be causing it...
                         

                        GSX Distributor shaft bearings

                        Two part topic:
                        1. Plastic bearing (#66) used in place of regular sealed bearing (#51) -- thoughts?

                        2. ANY of these bearings with the black support mount...
                         

                        The Legacy of the A2

                        I was recently disheartened to learn that a bowling center that I once serviced was actively looking to replace their A2's. I understand that most military bases and educational...
                         

                        Table turning on short stroke.

                        Hello dear Bowltech members.
                        First let me say thank you for your time. am plagued by a big issue for three weeks now.
                        our technician is working full time on another...
                         

                        Another pivot bearing broke.

                        One and a half year old GSX machines. This will be the 5th pivot bearing that has broke. This one decided to take out a few things with it. Snapped the stroke limiter shock stud...
                        Working...
                        X