Announcement

Collapse
No announcement yet.

Quiz On The Home Page Is Not Accurate

Collapse

Adsense Classic 1

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Quiz On The Home Page Is Not Accurate

    The Quiz On The Home Page Isn't Fair. One Of The Questions Was The Measurement For The Width Of A Spotting Cup On An 82-70 Mach.Your Choices Were:A)4 1/2,B)4 1/8,C)4 5/8,D)5 inches.In Which You Dont Even Get The Choice To Pick 4 1/4 Which is The Answer Because I Got The Answer From The "AMF GOD" Himself (John Isbell-82-70 Technical Trainer For AMF), & The Answer Is In The Service Manual. Thanx Guys.

  • #2
    Re: Quiz On The Home Page Is Not Accurate

    Is 4 1/4 a brunswick cup???????? [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]

    Comment


    • #3
      Re: Quiz On The Home Page Is Not Accurate

      No,It's Amf,If Not Sure Measure Your Cup Guage

      Comment


      • #4
        Re: Quiz On The Home Page Is Not Accurate

        Jim- You was robbed! [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]

        Comment


        • #5
          Re: Quiz On The Home Page Is Not Accurate

          Just hammer the cup till it spos pins [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]

          Comment


          • #6
            Re: Quiz On The Home Page Is Not Accurate

            the official back in the 70's was 4 1/8" +/- 1/8"

            however i agree with the king, hammer it til it spots.

            Comment


            • #7
              Re: Quiz On The Home Page Is Not Accurate

              my guage was/is 4 inch ball peen hammer, if it doesnt fit through the tips with room to spare, its "hammer time!!"

              Comment


              • #8
                Re: Quiz On The Home Page Is Not Accurate

                Originally posted by Ar Rar:
                Jim- You was robbed! [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img]
                <font size="2" face="Verdana, Helvetica, sans-serif">LMAO [img]/content/btubb/images/%%GRAEMLIN_URL%%/laugh.gif[/img] Good one Ar Rar.

                Comment


                • #9
                  Re: Quiz On The Home Page Is Not Accurate

                  Comment


                  • #10
                    Re: Quiz On The Home Page Is Not Accurate

                    Hey guy's,
                    I would'nt use a hammer on the spotting cups,you will find it quicker and easier with a big shifter.
                    willey.
                    always doing my best.

                    Comment


                    • #11
                      Re: Quiz On The Home Page Is Not Accurate

                      "Don't hammer the cup if you're hammered."
                      You may end up with aluminum scrap all over the deck.

                      Comment

                      Topic Starter RibbonScript

                      Collapse

                      Adsense Classic 2

                      Collapse
                      widgetinstance 666 (Related Topics) skipped due to lack of content & hide_module_if_empty option.
                       

                      Rake sweeping out of time, and pin launching onto lane.

                      I work on some nice old Brunswick A-2 pin setters. Most issues I've come across haven't been to problematic to figure out. But being I can't seem to get it to recreate the issue...
                       

                      Strange sweep problem

                      I’m a rookie mechanic and have been working on pinsetters for 2 years. One of my lanes has a problem with a sweep possibly coasting. I don’t know what could be causing it...
                       

                      GSX Distributor shaft bearings

                      Two part topic:
                      1. Plastic bearing (#66) used in place of regular sealed bearing (#51) -- thoughts?

                      2. ANY of these bearings with the black support mount...
                       

                      The Legacy of the A2

                      I was recently disheartened to learn that a bowling center that I once serviced was actively looking to replace their A2's. I understand that most military bases and educational...
                       

                      Table turning on short stroke.

                      Hello dear Bowltech members.
                      First let me say thank you for your time. am plagued by a big issue for three weeks now.
                      our technician is working full time on another...
                       

                      Another pivot bearing broke.

                      One and a half year old GSX machines. This will be the 5th pivot bearing that has broke. This one decided to take out a few things with it. Snapped the stroke limiter shock stud...
                      Working...
                      X