Announcement

Collapse
No announcement yet.

82-70 continous cycle (non-stop)

Collapse

Adsense Classic 1

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • 82-70 continous cycle (non-stop)

    you all are awsome, i just encounterd another problem, argh....

    i have a machine that will not stop cycling.
    any ideas?

    Thanx, Jeremy
    just feeling my way out like a blind man at an orgy.

  • #2
    Re: 82-70 continous cycle (non-stop)

    just swapped chasis with good one, problem persists. grim......
    just feeling my way out like a blind man at an orgy.

    Comment


    • #3
      Re: 82-70 continous cycle (non-stop)

      found the problem, i had to reset the "12-strike" scoring system.

      thank-you to all again with my previous problems, you guys rock!
      just feeling my way out like a blind man at an orgy.

      Comment


      • #4
        Re: 82-70 continous cycle (non-stop)

        If it didn't move with the chassis, all it tells you is that it's in the machine wiring.

        Causes of continuous:

        Stuck or broken cycle switch on the cushion

        Stuck/shorted cycle switch on the backend control panel

        Stuck/shorted 10th frame switch on the ball return up front

        A short or wire off & grounding on any of these devices.

        If you still use cushion cycle switches, look there first... that is the most common one. Make sure that the little spring that holds the plate against the switch hasn't come off. Easy way to check it is to pull a wire off the switch. If the machine stops cycling, there's your problem.
        <span style="font-style: italic">Educatio est omnium efficacissima forma rebellionis</span>

        Comment


        • #5
          Re: 82-70 continous cycle (non-stop)

          nice post GMan143.if this problem returns disconnect the wires in the box on the wall adjacent to the two machines. This is called the A &amp; MC box and in it you will see 8 terminals for each machine. Pull out the wires going to 1 and 2 on the problem side, but do not allow them to touch each other. If the machine stops cycleing the problem is from the top end ball return to the box. if the machine continues to cycle it is a short on the machine.,somewhere in your start switch area.
          Good luck from Scotland

          Comment

          Topic Starter RibbonScript

          Collapse

          Adsense Classic 2

          Collapse
          widgetinstance 666 (Related Topics) skipped due to lack of content & hide_module_if_empty option.
           

          Well this is a first.

          We all from time to time have one of those “wow I’ve never seen THAT before” moments. Well today was one of those for me when my night tech texts me to say lane 16 is out...
           

          Ball return wheel guide roller removal.

          Hey guys, i could just use a bit of advice trying to get this part out, first time I've had to do one of these. I got it to move a few turns but its come to a point where it has...
           

          Even old mechanics find something new.

          All my years working on these things I never had this happen…… until last week. ...
           

          82-90XL Frontend Gearbox Parts - Rebuild Woes

          We have 5 of the 088000365 replacement gear kits on the shelf, and I pulled two gearboxes off machines earlier this week, so I thought I'd try my hand at rebuilding them and save...
           

          Prolane damage

          Can this be repaired?
           

          LED Ball Lights

          Made an LED conversion for A2's and Frameworx masks. It can also be modded for the Harmony masks to accept 2 x 5mm led's and/or a 12v supply. Once I'm happy with the performance/design...
          Working...
          X