Swapping wires.

[Pin_Head Member Find all posts View Profile Close Pin_Head]

G'day again fellas.
This may seem really stupid but its just a matter of i cant remember which ones etc, what it is im after is someone who could tell me what wires i have to swap to get the sweep to lift up with the table simultaniously as it is now with my old 5 boards the sweep raises up while the table is still at spot and respot height.Sorry for the stupid question just its been years since i did it last i worked for the last 5 years almost with Omega-Teks.
Cheers Brett. [img]/content/btubb/images/%%GRAEMLIN_URL%%/confused.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/confused.gif[/img]

[Jimmy Jam Banned Find all posts View Profile Close Jimmy Jam]

Re: Swapping wires.

ts-10 and ts-32

[Pin_Head Member Find all posts View Profile Close Pin_Head]

Re: Swapping wires.

Do you mean swap the wire from ts-10 and connect it to t-32 and vise-versa?
I thought you swapped wires on the actual cam micro switches?

[8270_Wang Find all posts View Profile Close 8270_Wang]

Re: Swapping wires.

pin_head

It doesnt matter where you swap the wires. Check out this thread for further information. <a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank"><a href="http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014" target="_blank">http://www.bowltech.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=2;t=002014</a></a></a></a></a></a></a></a></a> It might give you more information

Wang

[Jimmy Jam Banned Find all posts View Profile Close Jimmy Jam]

Re: Swapping wires.

What I did Pin_head is remove RusselStoll cover and with a flashlight find the wire on ts-10 going to the cam switches and unplug'd it. Then I did the same for the wire on ts-32 and plugged in onto ts-10 where I took the first wire off. Then I plugged the old ts-10 wire onto ts-32 terminal.

I think on the first one I took off the wire channel cover under the chassis too. But found out you can get to them by just taking off the RusselStoll cover if you can get your hand in there. All your doing is swopping ta-1NO and ta-2NO.

[Pin_Head Member Find all posts View Profile Close Pin_Head]

Re: Swapping wires.

Thanks fellas very much appreciated [img]/content/btubb/images/%%GRAEMLIN_URL%%/smile.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/smile.gif[/img] [img]/content/btubb/images/%%GRAEMLIN_URL%%/smile.gif[/img]

[Andrew Members Find all posts View Profile Close Andrew]

Re: Swapping wires.

Hey Brett, how did you get stuck with old 5 boards?? Which centre, if if may ask?

Cheers,
Andrew.