Announcement

Collapse
No announcement yet.

Accelerator motors

Collapse

Adsense Classic 1

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Accelerator motors

    I had a shaft break out of a accelerator motor, is there any cheaper place than Brunswick to but these motors without losing the quality of them.

    Just Wondering
    Maverick

  • #2
    Re: Accelerator motors

    Graingers sell the exact motor for much less

    Comment


    • #3
      Re: Accelerator motors

      You might want to get in touch with Murrey International <a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank"><a href="http://www.murrey.com" target="_blank">http://www.murrey.com</a></a></a></a></a></a></a></a></a></a> and see how much there's cost. Since I don't do the parts ordering I'm not sure how much less theres would be as compared to Brunswick. We have been very pleased with there acc. motors (correct me if I'm worng but they look like there made by Leeson). Grainger's motor will also give you long life but keeping them cleaned and lubed is critical. The Dayton's we have use the sleeve bearings and in the past we have had to toss some of them because the bearing wore down and caused the rotor in the motor to drag the field, but for the price it's not a bad deal. I guess some of the problems with the Daytons were probably caused by the short acc. belt bieng too tight, but they had a lot of miles on them too.

      Comment


      • #4
        Re: Accelerator motors

        We replaced all our accelerator motors with low Rpm motors...we have the ones we took off in storage that we sell for 25.00 a motor

        Peanut
        Peanut

        Comment


        • #5
          Re: Accelerator motors

          Peanut,
          I would be interested in knowing what motor you used as a replacement to the original (model#, manufacturer) I think a lower RPM motor would work well in this situation.

          Jerrid
          and then he said, "on your death bed, you will receive total consciousness" so I got that going for me...... which is nice!

          Comment


          • #6
            Re: Accelerator motors

            Murrey currently offers the Murrey/Leeson Accelerator Motor(both the standard RPM and the slow speed). Call us for all specs and details. As always, we can always be reached at 800-421-1022.

            Quote:]Originally posted by jerrid:
            Peanut,
            I would be interested in knowing what motor you used as a replacement to the original (model#, manufacturer) I think a lower RPM motor would work well in this situation.

            Jerrid
            [/QUOTE]

            Comment


            • #7
              Re: Accelerator motors

              Hey Peanut, I'm interested in getting a couple of them motors from you. Just let me know where I can send the money and all that other stuff.

              Thanks
              Maverick

              Comment


              • #8
                Re: Accelerator motors

                jerrid
                the motors we went to were from Grainger
                (Part # 6K438) 1725 rpm

                Maverick
                please e-mail me at masternut@bowlingtech.com

                for details on motors

                peanut
                Peanut

                Comment

                Topic Starter RibbonScript

                Collapse

                Adsense Classic 2

                Collapse
                widgetinstance 666 (Related Topics) skipped due to lack of content & hide_module_if_empty option.
                 

                Rake sweeping out of time, and pin launching onto lane.

                I work on some nice old Brunswick A-2 pin setters. Most issues I've come across haven't been to problematic to figure out. But being I can't seem to get it to recreate the issue...
                 

                Strange sweep problem

                I’m a rookie mechanic and have been working on pinsetters for 2 years. One of my lanes has a problem with a sweep possibly coasting. I don’t know what could be causing it...
                 

                GSX Distributor shaft bearings

                Two part topic:
                1. Plastic bearing (#66) used in place of regular sealed bearing (#51) -- thoughts?

                2. ANY of these bearings with the black support mount...
                 

                The Legacy of the A2

                I was recently disheartened to learn that a bowling center that I once serviced was actively looking to replace their A2's. I understand that most military bases and educational...
                 

                Table turning on short stroke.

                Hello dear Bowltech members.
                First let me say thank you for your time. am plagued by a big issue for three weeks now.
                our technician is working full time on another...
                 

                Another pivot bearing broke.

                One and a half year old GSX machines. This will be the 5th pivot bearing that has broke. This one decided to take out a few things with it. Snapped the stroke limiter shock stud...
                Working...
                X